Hardware Specification
Page 3
...(hereinafter referred to as drive). OUTLINE The outline of this drive is hardware specification of the TEAC DW-224E-R93 built-in Table 2-1. (Table 2-1) Outline of the specification Model name TEAC P/N Applicable safety standards Data transfer rate (burst) Average access time Disc speed (24X CAV ...-ROM), average by TEAC standards 5,090min-1 (Approx) IDE (ATAPI) +5VDC 19sec max CD/CD-ROM (12cm, 8cm) CD-R (Recorded) CD-RW (Recorded) DVD-ROM DVD-R (Recorded) DVD-RW (Recorded) DVD-RAM (Recorded) DVD+R (Recorded) DVD+RW (Recorded) CD-R/RW disc (Refer to "DW-224E-C Software Specification". 2.
...(hereinafter referred to as drive). OUTLINE The outline of this drive is hardware specification of the TEAC DW-224E-R93 built-in Table 2-1. (Table 2-1) Outline of the specification Model name TEAC P/N Applicable safety standards Data transfer rate (burst) Average access time Disc speed (24X CAV ...-ROM), average by TEAC standards 5,090min-1 (Approx) IDE (ATAPI) +5VDC 19sec max CD/CD-ROM (12cm, 8cm) CD-R (Recorded) CD-RW (Recorded) DVD-ROM DVD-R (Recorded) DVD-RW (Recorded) DVD-RAM (Recorded) DVD+R (Recorded) DVD+RW (Recorded) CD-R/RW disc (Refer to "DW-224E-C Software Specification". 2.
Hardware Specification
Page 9
... : 70dB or more (1kHz, 20kHz LPF) (g) Output level : 0.8Vrms ±3dB (load = 47kΩ ATT = 0dB) (h) Muting : each channel independent (using the ATAPI command) (i) Volume : Software volume using the ATAPI command; 255 steps from volume level 0 to 2) (d) Ultra DMA : 33.3MB/sec max (4) Starting time (a) When power is switched on/when...
... : 70dB or more (1kHz, 20kHz LPF) (g) Output level : 0.8Vrms ±3dB (load = 47kΩ ATT = 0dB) (h) Muting : each channel independent (using the ATAPI command) (i) Volume : Software volume using the ATAPI command; 255 steps from volume level 0 to 2) (d) Ultra DMA : 33.3MB/sec max (4) Starting time (a) When power is switched on/when...
Hardware Specification
Page 33
... rather than cleaning it is possible using the power management command (STANDBY, STANDBY IMMEDIATE) or START/STOP UNIT command. For details, refer to the Software Specification. The timer will be preset using the timer in the drive: After executing (2), (3) and (4) in 15.2, if the specified time elapses ... IMMEDIATE) or START/ STOP UNIT command: The transition from the active to the idle mode is entered. 16. For details, refer to the Software Specification. (3) When the power is switched ON or a disc is not detected by the disc detection operation while the tray is being retracted, ...
... rather than cleaning it is possible using the power management command (STANDBY, STANDBY IMMEDIATE) or START/STOP UNIT command. For details, refer to the Software Specification. The timer will be preset using the timer in the drive: After executing (2), (3) and (4) in 15.2, if the specified time elapses ... IMMEDIATE) or START/ STOP UNIT command: The transition from the active to the idle mode is entered. 16. For details, refer to the Software Specification. (3) When the power is switched ON or a disc is not detected by the disc detection operation while the tray is being retracted, ...