Stihl 420 Support and Manuals
Stihl 420 Videos
Popular Stihl 420 Manual Pages
Instruction Manual - Page 6
... recommended. To reduce the risk of burn injury, STIHL recommends wearing clothing made of leather, wool, flame-...and help to protect your head.
4
TS 410, TS 420 Steel-toed safety boots are flammable - WARNING
Loose objects may...'s
instructions. Replace immediately any obstacles or moving parts of vibration created by the cutting wheel.
Most fabrics used in concrete or...
Instruction Manual - Page 7
... a cut -off machine models are recommended. Only STIHL branded parts and cutting attachments expressly approved by NIOSH for the material being cut and appropriate for worksite-specific conditions anytime wet cutting at the flow rate recommended in this instruction manual is likely to the respirator needed for worksite-specific conditions.
TS 410, TS 420
5 Even if wet cutting...
Instruction Manual - Page 8
... result in reactive forces and present other sources of heat. Wheels that , under certain circumstances, can result in this instruction manual. Wobbling, for cutting aggregate concrete.
4.
WARNING
Inspect the composite cutting wheel frequently and replace immediately if it is not exposed to particularly high bending and compression stress, which the wheel was not designed...
Instruction Manual - Page 9
... carrying it for cutting concrete, asphalt, natural stone, clay pipe, brick and the like. The abrasive cutting wheel continues to a stop by vehicle: Properly secure your STIHL cut -off machine....machine.
Fuel
Your STIHL cut -off machine uses an oilgasoline mixture for cutting all metals or other reactive forces. See the chapter "Fuel" in this instruction manual. TS 410, TS 420
7
Instruction Manual - Page 11
... incorrect setting, the tensioning procedure must be followed as this manual. Never mount or use a tool to open by an authorized STIHL servicing dealer ...installation, follow the procedure described in the chapter "Mounting an Abrasive Cutting Wheel" in this instruction manual. WARNING
Check the fuel system for fuel leakage while refueling and during operation. Have the machine repaired...
Instruction Manual - Page 16
...stone, concrete and ...420 If a cut -off the engine and be reversed and work against the operator. The powerful forces used , sweep debris from the path of the cart's wheels may result in this instruction manual.
2. Large bending stresses occur during such work . Run each new wheel immediately after installation...cutting wheels:
1.
STIHL recommends the use a...rotating before setting the cut...
Instruction Manual - Page 18
... segments or exhibit other operational problems that will not "sag" or "drop." Always pay attention in the market. Where there is under stress because of certain non-STIHL branded wheels may be at...may begin to be broken manually using the bottom of the wheel, with a bell end or when cutting out a section of pipe in a trench that, if not properly supported, can propel the cut-...
Instruction Manual - Page 19
... injury from loss of the cutting attachment. Position the cut -off machines are using only STIHL branded abrasive cutting wheels properly rated for the user and the fall of the severed portion of...with abrasive material on their sides. TS 410, TS 420
17 Maintain good balance and footing at all dangers presented by circular saw blades, carbide-tipped blades or toothed blades of any ...
Instruction Manual - Page 20
...only STIHL replacement parts for maintenance and repair....your authorized STIHL servicing dealer. ...parts manufactured by others may be extremely dangerous and could ignite combustible fumes and
18
TS 410, TS 420...manual as this instruction manual. Be alert to rotate for prying or shoveling away any maintenance or repair work not described in the cut above shoulder height.
11. Support...
Instruction Manual - Page 21
...-off valve. Forest Service, may occur that you... of the Public Resources Code to produce the recommended flow... machine. TS 410, TS 420
19 The operator should contact ...STIHL for laws or regulations relating to the warranty statement near the end of this manual. For proper dust suppression, always ensure that could ignite combustible fumes and cause a fire.
The highest flow setting...
Instruction Manual - Page 29
... abrasive cutting wheels, circular saw blades, carbide-tipped blades, rescue blades or wood cutting tooth blades of severe or fatal injury. TS 410, TS 420
27 Stone (hard rock)... any other substances, including wood and plastic. Abrasive concrete
- material you are cutting. Cut-off machine.
Diamond Cutting Wheels
STIHL diamond cutting wheels are cutting. The designation on the...
Instruction Manual - Page 39
...This problem can cause ...proper adjustments and repairs. To ensure ...motors, snowmobiles, chain saws, mopeds, etc.)....420
37 If your cut-off machine's idle speed is incorrectly adjusted, have your authorized STIHL servicing dealer check your STIHL...instructions that you use a fresh, high quality 2-cycle engine oil.
STIHL MotoMix uses STIHL HP Ultra two-stroke engine oil suited for use only STIHL...
Instruction Manual - Page 47
..., non-threaded terminals
TS 410, TS 420
45
Arcing may occur that have caused fouling...plug terminal (2).
See specifications
N Install the spark plug by STIHL. operating at part throttle.
000BA039 KN
WARNING...Specifications"
N Use only resistor type spark plugs of fire and burn injury, use only spark plugs authorized by hand and screw it in this instruction manual
Correct the problems...
Instruction Manual - Page 56
... Warranty Policy, available at an authorized dealer), parts and labor.
STIHL Incorporated must be repaired or replaced by calling 1-800-GO-STIHL (1-800-467-8445).
Owner's Warranty Responsibilities
As the small off -road equipment engine or a part has failed due to the ultimate purchaser.
Any replacement part or service that STIHL Incorporated may be obtained from defects in...
Instruction Manual - Page 57
..., at no cost to obtain warranty service. STIHL Incorporated is a need to communicate repair or recall information about your small off-road equipment engine will be used for any independent test laboratory. Carburetor (if applicable)
- Intake Manifold
- Fly Wheel
- Fuel Cap
-
Any warranted part which is not scheduled for replacement as required maintenance, or which cause...
Stihl 420 Reviews
Do you have an experience with the Stihl 420 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Stihl yet.
Earn 750 points for your review!