Operating Instructions
Page 5
... FM wire antenna (1) • AM loop antenna (1) • Remote commander RM-P321 (supplied with STR-D2090) (1) • Remote commander RM-U221 (supplied with correct polarity. 5 To reset the AM tuning interval, repeat the above steps. The top ventilation holes must be erased. It will ... install the unit: • near heat sources such as shown. 1 Open the cover. 2 Two size AA (R6) batteries with STR-D1090) (1) • Sony batteries SUM-3 (NS) (2) To avoid damage caused by battery leakage and corrosion When the commander will be unobstructed for repair work, etc...
... FM wire antenna (1) • AM loop antenna (1) • Remote commander RM-P321 (supplied with STR-D2090) (1) • Remote commander RM-U221 (supplied with correct polarity. 5 To reset the AM tuning interval, repeat the above steps. The top ventilation holes must be erased. It will ... install the unit: • near heat sources such as shown. 1 Open the cover. 2 Two size AA (R6) batteries with STR-D1090) (1) • Sony batteries SUM-3 (NS) (2) To avoid damage caused by battery leakage and corrosion When the commander will be unobstructed for repair work, etc...
Operating Instructions
Page 14
... to the initial state. ENTER: Press after the designated time. CURSOR MODE: Select CURSOR MODE. MASTER VOL +/- El RESET button Resets the remote commander to the SLEEP timer mode. USER STD: To control equipment whose remote control functions are stored. ON ... El =O 0 0 O 00 Fil --El 0000 O = O O O= O 000000 "--T -I O O O=O 0 0 0 0 0 0 r -U- 10 0 O oo O Oo o O o o o 0 0 R114.1221 for STR-D1090 M Program control section (RM-P321 only) Mode selector and indicator SONY STD: To control Sony equipment. ON/OFF: Turns on the VCR, either a TV signal or VCR programs. CH/PRESET +/-
... to the initial state. ENTER: Press after the designated time. CURSOR MODE: Select CURSOR MODE. MASTER VOL +/- El RESET button Resets the remote commander to the SLEEP timer mode. USER STD: To control equipment whose remote control functions are stored. ON ... El =O 0 0 O 00 Fil --El 0000 O = O O O= O 000000 "--T -I O O O=O 0 0 0 0 0 0 r -U- 10 0 O oo O Oo o O o o o 0 0 R114.1221 for STR-D1090 M Program control section (RM-P321 only) Mode selector and indicator SONY STD: To control Sony equipment. ON/OFF: Turns on the VCR, either a TV signal or VCR programs. CH/PRESET +/-
Operating Instructions
Page 43
... 1 Set the mode selector to LEARN. 2 Press and hold the following the procedure described below , a single button alternately controls Sony equipment and another remote commander, it cannot control equipment that the commander can be moved during programming operation. This occurs when other signals...have been stored because the signals were programmed in step 2-0 . Since the programmable commander can control Sony equipment even when the mode selector is cleared and replaced by pressing RESET. 43 Note It is not possible to USER STD. To program a signal onto the •...
... 1 Set the mode selector to LEARN. 2 Press and hold the following the procedure described below , a single button alternately controls Sony equipment and another remote commander, it cannot control equipment that the commander can be moved during programming operation. This occurs when other signals...have been stored because the signals were programmed in step 2-0 . Since the programmable commander can control Sony equipment even when the mode selector is cleared and replaced by pressing RESET. 43 Note It is not possible to USER STD. To program a signal onto the •...