Smeg KSEU912X Support and Manuals
Get Help and Manuals for this Smeg item
View All Support Options Below
Free Smeg KSEU912X manuals!
Problems with Smeg KSEU912X?
Ask a Question
Free Smeg KSEU912X manuals!
Problems with Smeg KSEU912X?
Ask a Question
Smeg KSEU912X Videos
Smeg KSEU912X Hotte
Duration: :40
Total Views: 3
Duration: :40
Total Views: 3
Popular Smeg KSEU912X Manual Pages
User Guide - Page 1
...3. Installation and service must be performed by a qualified installer, service agency or the gas supplier. INSTRUCTIONS FOR THE INSTALLER: these are intended for the qualified engineer who is able to install, ...Follow the gas supplier's instructions. • lf you cannot reach your safety, the information in this or any phones in the vicinity of this manual must be followed to ...
User Guide - Page 2
... AND SAVE THESE INSTRUCTIONS -
Important Safety Instruction
1.
Your Safety And the Safety of Massachussets, the following installation instructions apply: - Installation and service must be performed by a qualified or licensed contractor, plumber, or gasfitter
qualified or licensed by a qualified installer, service agency or the gas supplier. Installations and repairs must be...
User Guide - Page 3
COOKTOP MEASUREMENTS
5 Instructions for the Installer 2.
User Guide - Page 4
...
connection must be followed when attaching the appliance to the support structure.
6 Instructions for easy reference whenever needed. 2 Temporarily remove all removable parts from strong draft areas, such as it should be installed in the tables referring to the figure below : 1 Remove all governing codes and ordinances. Cabinet opening dimensions that could fall and cause...
User Guide - Page 5
G 28 3/8"
720 mm
Gas line opening Wall: everywhere, 5" (12.7 cm) below underside of the cut out drawer.
7 Instructions for the Installer
Cooktop widht 28 3/8"
720 mm
A 27 1/2"
700 mm
B 19 3/8"
492 mm
MINIMUM DISTANCE
C
D
E
8 1/4"
2 "
2 "
210 mm 50 mm 50 mm
F 13/16" - 2 "
20 - 50 mm
NOTE: ...
User Guide - Page 6
...Instructions for turning on or shutting off gas to the cooktop.
- The valve is for the Installer...personnel, authorized gas company personnel, and authorized service personnel.
- In the absence of your ...Gas Code ANSI Z223.1 latest edition or CAN/CGA B149 - Securely tighten all government codes and ...when moving the cooktop. If local codes permit, a flexible metal appliance connector...
User Guide - Page 7
... back of the oven, as follows for the Installer
The regulator must be provided.
9 Instructions for operation and monitoring of
4) the regulator setting: - The cooktop and its individual shut-off valve must be disconnected from the gas supply piping system by closing the respective manual shutoff valve during any pressure testing of 14" (35...
User Guide - Page 8
...available, it is equipped with the National ANSI/NFPA 70 Electrical Code (latest edition*) or the Canadian Electrical Code (CSA)** and local codes and ordinances. Copies of the customer to have a properly polarized and grounded, 3-prong outlet installed by a qualified electrician. Instructions for the Installer
3.2.1 Recommended Grounding Method For your personal safety, this cooktop must...
User Guide - Page 9
... supports and the box. Leak testing of the appliance shall be conducted according to the manufacturer's instructions.
2)
The following procedures must be performed to adjust the gas supply pressure for the Installer 4. Instructions ...for LP operation of the cooktop: 1 Unscrew cap A on the pressure regulator 2 Turn it to the part where LP is an...
User Guide - Page 10
... be certain tubing is not kinked.
12 Use pipe-joint compound made for the Installer
Carefully position the gasket provided all of the brackets supplied with NATURAL and L.P.
...has been set in place.
1)
2)
3) NOTE: Use all around the outer edge of the hole inthe work surface as shown in picture 2 below refer to the supporting structure, adjusting it adheres properly. Instructions for ...
User Guide - Page 11
... gas connection A before fixing the hob.
Always place a suitable sealing medium (such as Teflon tape) between pressure regulator D and adaptator C and between fitting A adaptator C. Instructions for the Installer
Always use pipe-joint compound made for use with the ignition plugs and the thermocouples.
7) Plug power supply cord into grounded outlet.
13 GAS...
User Guide - Page 12
...supplied to check for proper operation.
1) Check for the Installer
5. Check operation again. Never test for proper tightness....do not light properly, turn the control knob to the support structure, some simple procedures are in the proper position. Failure...parts have checked to ensure that burner caps and crowns are required to the appliance. lf a burner does not light at this instruction...
User Guide - Page 13
Verify proper operation after servicing.
15 WARNING
Label all wires prior to disconnection when servicing controls. Instructions for the Installer
6.
WIRING DIAGRAMS
The power cord on this appliance is equipped with a threee pronge polarized plug (grounding) which mates with standard three pronged (grounding) wall receptacles. Wiring errors can cause improper and dangerous operation.
Smeg KSEU912X Reviews
We have not received any reviews for Smeg yet.