R-1750 , R-1751 , R-1752 , R-1754 Microwave Operation Manual
Page 4
... 1-800-BE-SHARP OR VISIT www.sharp-usa.com. This...Sharp be the sole and exclusive remedy available to have this additional period. Nor shall Sharp...Obtain Service: From a Sharp Authorized Servicer located In...Sharp Authorized Servicer, call Sharp toll free at no extra charge, provided it is in case of Sharp. CONSUMER LIMITED WARRANTY SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp... to purchasers by Sharp and shall be ... and responsibilities of Sharp to the purchaser ...remanufactured equivalent at 1-800-BE-SHARP (1-800-237-4277). Correction...
... 1-800-BE-SHARP OR VISIT www.sharp-usa.com. This...Sharp be the sole and exclusive remedy available to have this additional period. Nor shall Sharp...Obtain Service: From a Sharp Authorized Servicer located In...Sharp Authorized Servicer, call Sharp toll free at no extra charge, provided it is in case of Sharp. CONSUMER LIMITED WARRANTY SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp... to purchasers by Sharp and shall be ... and responsibilities of Sharp to the purchaser ...remanufactured equivalent at 1-800-BE-SHARP (1-800-237-4277). Correction...
R-1750 , R-1751 , R-1752 , R-1754 Microwave Operation Manual
Page 5
...is not designed for examination, repair or adjustment. 10. This appliance must be heated in the oven cavity: a. As with the provided installation instructions. 5. Remove wire twist-ties from heated surfaces. 14. Corrosive cleaning agents, such as whole eggs and sealed containers - See ...-Grease should not be followed, including the following: WARNING - IMPORTANT SAFETY INSTRUCTIONS When using the appliance. 2. Contact nearest Sharp Authorized Servicer for industrial or laboratory use above both gas and electric cooking equipment 36" wide or less. 11. Do not...
...is not designed for examination, repair or adjustment. 10. This appliance must be heated in the oven cavity: a. As with the provided installation instructions. 5. Remove wire twist-ties from heated surfaces. 14. Corrosive cleaning agents, such as whole eggs and sealed containers - See ...-Grease should not be followed, including the following: WARNING - IMPORTANT SAFETY INSTRUCTIONS When using the appliance. 2. Contact nearest Sharp Authorized Servicer for industrial or laboratory use above both gas and electric cooking equipment 36" wide or less. 11. Do not...
R-1750 , R-1751 , R-1752 , R-1754 Microwave Operation Manual
Page 6
...that a separate circuit serving only the oven be plugged into a wall receptacle that the microwave oven is on the door. Neither Sharp nor the dealer can result in the oven cavity. One set is equipped with a cord having a grounding wire with the dealer ...microwave oven to observe the correct electrical connection procedures. Radio or TV Interference Should there be grounded. WARNING - Electrical Requirements Check Installation Instructions for proper location for this oven. 1. If there is recirculated. Filler Panel Kit. Read enclosures and SAVE the Operation ...
...that a separate circuit serving only the oven be plugged into a wall receptacle that the microwave oven is on the door. Neither Sharp nor the dealer can result in the oven cavity. One set is equipped with a cord having a grounding wire with the dealer ...microwave oven to observe the correct electrical connection procedures. Radio or TV Interference Should there be grounded. WARNING - Electrical Requirements Check Installation Instructions for proper location for this oven. 1. If there is recirculated. Filler Panel Kit. Read enclosures and SAVE the Operation ...
R-1750 , R-1751 , R-1752 , R-1754 Microwave Operation Manual
Page 36
... cover, remove the screw on use. Bulbs are also available at most hardware stores or lighting centers. Pull the louver away from a Sharp Authorized Servicer or parts distributor. Push in the cavity faceplate openings. To replace light bulb, first disconnect power to ensure that the three ...bottom clips snap into place and replace the louver mounting screw. Push the louver back into the cavity faceplate. See page 6 for nonvented, recirculated installation. DO NOT USE BULB LARGER THAN 30 WATTS. 4. DO NOT USE A BULB LARGER THAN 30 WATTS. 4. Do not touch glass when ...
... cover, remove the screw on use. Bulbs are also available at most hardware stores or lighting centers. Pull the louver away from a Sharp Authorized Servicer or parts distributor. Push in the cavity faceplate openings. To replace light bulb, first disconnect power to ensure that the three ...bottom clips snap into place and replace the louver mounting screw. Push the louver back into the cavity faceplate. See page 6 for nonvented, recirculated installation. DO NOT USE BULB LARGER THAN 30 WATTS. 4. DO NOT USE A BULB LARGER THAN 30 WATTS. 4. Do not touch glass when ...
