Sharp KB-0333KW Support and Manuals
Get Help and Manuals for this Sharp item
View All Support Options Below
Free Sharp KB-0333KW manuals!
Problems with Sharp KB-0333KW?
Ask a Question
Free Sharp KB-0333KW manuals!
Problems with Sharp KB-0333KW?
Ask a Question
Popular Sharp KB-0333KW Manual Pages
KB-0333K Operation Manual / Installation Instructions - Page 1
1
1
"
KB-0333K
&OLLOWEDBYINDICATINGCOLOR+ BLACK 7 WHITE 3 STAINLESSSTEEL
INSIGHT RANGE HOOD
",Ê
1
" -1 7,, /9 1
9Ê -/,1
x n
"
/Ê7 n
" ‡ 1
1
KB-0333K Operation Manual / Installation Instructions - Page 2
...
/
/
SERIAL NUMBER
TELEPHONE TELEPHONE
TO PHONE:
DIAL DIAL
1-800-BE-SHARP (237-4277) for: SERVICE (for your nearest Sharp Authorized Servicer) PARTS (for your authorized parts distributor) 1-800-642-2122 for: Charcoal Filters (model KBK-330)
TO WRITE:
Sharp Electronics Corporation Customer Assistance Center 1300 Naperville Drive Romeoville, IL 60446-1091
Please provide the following...
KB-0333K Operation Manual / Installation Instructions - Page 3
... nearest Sharp Authorized Servicer, call Sharp toll free at 1-800-BE-SHARP (1-800-237-4277). Be sure to the purchaser for parts or labor for the period(s) set forth below . CONSUMER LIMITED WARRANTY
SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the "Product"), when shipped in its option, either repair the defect or replace...
KB-0333K Operation Manual / Installation Instructions - Page 4
...instructions and Cleaning information are on low or medium settings. Always use this manual with an additional speed control device.
7. If you have a Class ABC extinguisher and you have questions, contact Sharp at service panel and lock the service disconnecting means to prevent backdrafting. Installation...10. D. CAUTION
1. Please read specification label on fan or filter.
4....
KB-0333K Operation Manual / Installation Instructions - Page 5
... (3 1⁄4" x 10" or 7" round), horizontally (3 1⁄4" x 10" only) or be non-ducted. For a non-ducted installation, DO NOT cut a duct access hole.
31/4" X 10" HOOD MOUNTING SCREWS (4) VERTICAL DUCTING
1315/16" (30" hood) CABINET FRONT... proper placement of transitions and elbows. For vertical or horizontal discharge, run ductwork between service panel and hood location.
5
KB-0333K Operation Manual / Installation Instructions - Page 6
... knockout and install approved Electrical Cable Clamp. Teflon® is a registered trademark of DuPont.
4 Remove Damper/ Duct Connector from hood. Set connector aside ...Baffle from top of hood.
6 Set duct plate aside - This will be heard when fully installed. PREPARE THE HOOD
1 Remove 7"...-DUCTED INSTALLATION - Set cover and mounting screws aside. with mounting screws.
2 ...
KB-0333K Operation Manual / Installation Instructions - Page 7
... To accommodate off -center installations, one end of the duct connector may need to be installed up to top/back edge...install air chute and screw, re-connect wire harness and replace light panel. Damper flap must open freely in Step #1 under "PREPARE THE HOOD".
Install...with two screws.
14 7" Round Ducted Discharge Only: Re-install 7" Round Duct Plate removed in direction of airflow (away...
KB-0333K Operation Manual / Installation Instructions - Page 8
...Connect house black to hood black wire, house white to motor. Set aside for later. Check that wheel is switched off at the service panel. Use a piece
of electric shock, make sure power is... service panel to prevent power from being switched on accidentally. 1 Connect House Wiring (120 VAC) to the Stop Edge of the blower wheel and down until it is locked in place. To install ring:
1. Replace ...
KB-0333K Operation Manual / Installation Instructions - Page 9
.... 1 Hang hood from Sharp (see page 2). Tighten mounting screws securely. If hood is to make joints secure and air tight.
5 Replace filters, turn on power at service panel and test for proper operation.
NON-DUCTED FILTERS
• Attach charcoal filters to hood. Use duct tape to be installed Non-Ducted:
• Purchase a set of (4) keyholes...
KB-0333K Operation Manual / Installation Instructions - Page 10
... and part numbers are: Littlefuse, 217010; Bussmann, GMA10A; Remove filters, bottom panel, light wire harness and air chute.
3. After replacing the cleaned filters (or installing new ones...Sharp Insight Range Hood is elevated. If it is not open (blown), additional diagnostics need to protect it is time to the original setting.
• If the fan is off, the Sensor will flash on at service...
KB-0333K Operation Manual / Installation Instructions - Page 11
...replaced. Make sure all grease-laden surfaces.
Do not use abrasive cloth, steel wool pads or scouring powder on the Teflon®-coated bottom cover or on any painted surface. Do not oil or disassemble motor.
ducted installations...trademark of electric shock, disconnect from power supply before re-installing filters and restoring power. Aluminum mesh filters: Clean frequently ...
KB-0333K Operation Manual / Installation Instructions - Page 12
This symbol on the nameplate means the product is listed by Underwriters Laboratories, Inc. SHARP ELECTRONICS CORPORATION • Sharp Plaza, Mahwah, New Jersey 07430-2135 626995B
PRINTED IN USA -
Sharp KB-0333KW Reviews
We have not received any reviews for Sharp yet.