Sharp KB-0333KK Support and Manuals
Get Help and Manuals for this Sharp item
View All Support Options Below
Free Sharp KB-0333KK manuals!
Problems with Sharp KB-0333KK?
Ask a Question
Free Sharp KB-0333KK manuals!
Problems with Sharp KB-0333KK?
Ask a Question
Popular Sharp KB-0333KK Manual Pages
KB-0333K Operation Manual / Installation Instructions - Page 1
1
1
"
KB-0333K
&OLLOWEDBYINDICATINGCOLOR+ BLACK 7 WHITE 3 STAINLESSSTEEL
INSIGHT RANGE HOOD
",Ê
1
" -1 7,, /9 1
9Ê -/,1
x n
"
/Ê7 n
" ‡ 1
1
KB-0333K Operation Manual / Installation Instructions - Page 2
...
DIAL DIAL
1-800-BE-SHARP (237-4277) for: SERVICE (for your nearest Sharp Authorized Servicer) PARTS (for your daytime telephone number (including area code) and description of purchase, your complete mailing address (including zip code), your authorized parts distributor) 1-800-642-2122 for: Charcoal Filters (model KBK-330)
TO WRITE:
Sharp Electronics Corporation Customer Assistance Center...
KB-0333K Operation Manual / Installation Instructions - Page 3
... warranty lasts, so the above exclusion may not apply to Sharp's Installation Instructions. CONSUMER LIMITED WARRANTY
SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the "Product"), when shipped in its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to...
KB-0333K Operation Manual / Installation Instructions - Page 4
...codes and standards.
4.
off the burner.
Homeowner: Operating instructions and Cleaning information are on fan or filter.
4. To reduce the risk of cooking impurities, your back to prevent backdrafting. Please read specification label on page 2 of fuel burning equipment to an exit.
* Based on low or medium settings... Sharp at high settings. Installer: Leave this manual....
KB-0333K Operation Manual / Installation Instructions - Page 5
... and elbows. For best results, use a minimum number of ductwork and electrical cutout in cabinet or wall. For a non-ducted installation, DO NOT cut a duct access hole.
31/4" X 10" HOOD MOUNTING SCREWS (4) VERTICAL DUCTING
1315/16" (30" hood)...(3 1⁄4" x 10" only) or be non-ducted. For vertical or horizontal discharge, run ductwork between service panel and hood location.
5
KB-0333K Operation Manual / Installation Instructions - Page 6
...when fully installed.
Set connector aside -
held in place with 2 screws)
5 Remove either top or back wiring knockout and install approved ... screws. The following Steps (6 thru 14) are for DUCTED INSTALLATION ONLY.
6 Remove Light Panel -
held in place. TEFLON®... finger holes and lift filters out. Set duct plate aside - Set cover and mounting screws aside. Pull ...
KB-0333K Operation Manual / Installation Instructions - Page 7
...). 10 Re-install air chute and screw, re-connect wire harness and replace light panel. Cut the ties, lift plate out, and discard plate.
Make sure damper Pivot is nearest to top/back edge of hood center or the 7" Round Duct Plate can be trimmed to trap wires between Support Fin and light...
KB-0333K Operation Manual / Installation Instructions - Page 8
...
of electric shock, make sure power is packed behind the Teflon®Coated Bottom Cover. Set aside for later. Reassemble wheel to hood white wire and house ground under Green Ground Screw...the service panel. Replace Retaining Ring from motor. Check that wheel is locked in place. Lock or tag service panel to prevent power from being switched on non-ducted filters, see page 9. To install ...
KB-0333K Operation Manual / Installation Instructions - Page 9
.... Be sure that the sides with the blue and yellow stripes are engaged in narrow end of (2) charcoal filters, model KBK-330, from your local distributor, retailer or from (4) mounting screws. Purchase bulbs separately.
2 Replace bottom cover.
3 Connect ductwork to be installed Non-Ducted:
• Purchase a set of (4) keyholes.
1 Hang hood from Sharp (see page 2).
KB-0333K Operation Manual / Installation Instructions - Page 10
...light level, press
button.
After replacing the cleaned filters (or installing new ones), press the "CLEAN FILTER" button to turn off the indicator light.
2
4
HEAT SENSOR
Your Sharp Insight Range Hood is a ... 4 will increase the fan setting when the temperature is not open (blown), additional diagnostics need to be done.
4. Common manufacturer and part numbers are pressed, but the...
KB-0333K Operation Manual / Installation Instructions - Page 11
.... it is a registered trademark of electric shock, disconnect from power supply before re-installing filters and restoring power. Teflon® is time to green when it must not ... before cleaning. Use a damp cloth and a mild detergent to be replaced.
Do not oil or disassemble motor. ducted installations): Clean filter surfaces frequently with a damp cloth and a mild detergent...
KB-0333K Operation Manual / Installation Instructions - Page 12
SHARP ELECTRONICS CORPORATION • Sharp Plaza, Mahwah, New Jersey 07430-2135 626995B
PRINTED IN USA
- This symbol on the nameplate means the product is listed by Underwriters Laboratories, Inc.
Sharp KB-0333KK Reviews
We have not received any reviews for Sharp yet.