Seagate ST400FX0012 Support and Manuals
Get Help and Manuals for this Seagate item
This item is in your list!
View All Support Options Below
Free Seagate ST400FX0012 manuals!
Problems with Seagate ST400FX0012?
Ask a Question
Free Seagate ST400FX0012 manuals!
Problems with Seagate ST400FX0012?
Ask a Question
Popular Seagate ST400FX0012 Manual Pages
Pulsar XT.2 SAS Product Manual - Page 3
... 8 4.6 Programmable drive capacity 8 4.7 Factory-installed options 8 4.8 ...specifications 14
6.1 Error rates 14 6.1.1 Unrecoverable Errors 15 6.1.2 Interface errors 15
6.2 Endurance Management 15 6.2.1 Wear Leveling 15 6.2.2 Garbage Collection 15 6.2.3 Write Amplification 15 6.2.4 UNMAP 15 6.2.5 Data Retention 16 6.2.6 Lifetime Endurance Management 16
6.3 Reliability and service...
Pulsar XT.2 SAS Product Manual - Page 4
... 35 8.2.2 Locking SP 36 8.2.3 Default password 36 8.3 Random number generator (RNG 36 8.4 Drive locking 36 8.5 Data bands 36 8.6 Cryptographic erase 37 8.7 Authenticated firmware download 37 8.8 Power requirements 37 8.9 Supported commands 37 8.10 RevertSP 37
9.0 Defect and error management 38
9.1 Drive internal defects/errors 38 9.2 Drive error recovery procedures 39 9.3 SAS system...
Pulsar XT.2 SAS Product Manual - Page 10
...Pulsar XT.2 drives support the SAS Protocol specifications to the model numbers listed in this manual applies to standard and Self-Encrypting Drive models. Note. The Self-Encrypting Drive models indicated on the cover of Data at Rest" based on Self-Encrypting Drive models. The data listed in this and other forms of Seagate Self-Encrypting Drive models were called Full Disk Encryption (FDE...
Pulsar XT.2 SAS Product Manual - Page 11
... in the appropriate sections of this manual and the Seagate SAS Interface Manual, part number 100293071. Special attention must meet any susceptibility performance requirements.
If the I /O cables may be given in the areas of the drive. Pulsar XT.2 SAS Product Manual, Rev. The drives depend on the "TCG Storage Architecture Core Specification" and the "TCG Storage Workgroup...
Pulsar XT.2 SAS Product Manual - Page 14
... as described in the ANSI specifications, this document, and the SAS Interface Manual (part number 100293071) which describes the general interface characteristics of populating their systems with Block Unmap Support • Silent operation • Lifetime Endurance Management
Pulsar XT.2 SAS Self-Encrypting Drive models have the following standard features:
• 1.5 / 3.0 / 6.0 Gb...
Pulsar XT.2 SAS Product Manual - Page 17
...
LBPME Supported Supported
LBPRZ Supported Not Supported
A logical block provisioning management enabled (LBPME) bit set to Physical Block Locations. A FORMAT command will be capable of performing a SCSI FORMAT UNIT command which supports LBA unmapping. Pulsar XT.2 SAS Product Manual, Rev. For more details on the storage medium until such a time as part of the Thin Provisioning model. In...
Pulsar XT.2 SAS Product Manual - Page 23
... been classified by the host as part of the Thin Provisioning feature set. Wear Leveling is automatically managed by the drive and requires no user interaction. 6.1.1
Unrecoverable Errors
An unrecoverable data error is defined as a failure of the drive to recover data from the same cause are treated as 1 error.
6.1.2
Interface errors
An interface error is defined as a failure of...
Pulsar XT.2 SAS Product Manual - Page 43
... known as gatekeepers to the drive security services. The 32-byte Data Encryption Key (DEK) is a random number which is in the computer, storage and digital communications industry. These act as "protection of data at rest." Seagate's SED models comply with the Trusted Computing Group (TCG) Enterprise Storage Specifications as it is generated by...
Pulsar XT.2 SAS Product Manual - Page 47
..., it can avoid placing data in the SAS Interface Manual. The DIE field contains the die number within the ... of idle time.
Status reporting plays a role in systems error management and its use in the T10 document SPC-4 available from ...service by the drive to system performance.
This is the default setting from BMS only impacts the first command that return unrecoverable errors...
Pulsar XT.2 SAS Product Manual - Page 48
... - Seagate products do not support Type 3.
9.6.2
Setting and determining the current Type Level
A drive is that the Protection Information bits can only be managed at LBA boundaries across the ... PI drive, transfers should be queried by the T10 SBC3 specification.
Type 2 does allow the use of PI
There are transmitted at anytime to indicate the PI Types supported and...
Pulsar XT.2 SAS Product Manual - Page 52
... provided in the SAS Interface Manual (part number 100293071).
11.1
SAS features
This section lists the SAS-specific features supported by Pulsar XT.2 drives.
11.1.1
Task management functions
Table 12 lists the SAS task management functions supported.
B Table 12: SAS task management functions supported
Task name Abort Task Abort task set Clear ACA Clear task set I_T Nexus Reset Logical...
Pulsar XT.2 SAS Product Manual - Page 58
...) on Port B.
See the appropriate SPC release documentation for Model ST400FX0012. An initiator can be changed only by downloading a complete set up new current and saved values, where the values are hard-coded in the drive firmware stored in the SAS Interface Manual. B
Refer to the values below for the drive to report its operating parameters to the initiator.
Pulsar XT.2 SAS Product Manual - Page 69
... 58 signal characteristics 59 specifications 22
61 Index
Numerics
12 volt pins 59
5 volt pins 59 6 Gbps 60
A
abort task set function 44 commands supported 46 condensation 30 condition met/good status 55 connector
illustrated 58 requirements 58 cooling 42 CRC error 15 Cryptographic erase 37 Current profiles 26 customer service 21
D
Data Bands 36...
Pulsar XT.2 SAS Product Manual - Page 71
...30 reliability 7
specifications 14 reliability and service 16 repair and return information 21 reporting actual retry count 55 reservation conflict status 55 resonance 30 return information 21 RNG 36
RoHS 4, 5
S
safety 3 SAS
interface 58 physical interface 55 task management functions 44 SAS documents 5
SAS Interface Manual 3, 5
SAS-2 Specification 60 SCSI interface
commands supported 46 Secure ID...
Pulsar XT.2 SAS Product Manual - Page 72
... task set 44 terminate task 44 task management response codes 44 Function complete 00 44 Function not supported 05 44 Function reject 04 44 task set full status 55 TCG 35 technical support services 1
temperature 29, 42
limits 29 non-operating 30 regulation 3 See also cooling terminate task function 44 Thin Provisioning 9 transmitters 59 transporting the drive 21...
Seagate ST400FX0012 Reviews
Do you have an experience with the Seagate ST400FX0012 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Seagate yet.
Earn 750 points for your review!