Seagate ST3600002FC - Cheetah 600 GB Hard Drive Support and Manuals
Get Help and Manuals for this Seagate item
View All Support Options Below
Free Seagate ST3600002FC manuals!
Problems with Seagate ST3600002FC?
Ask a Question
Free Seagate ST3600002FC manuals!
Problems with Seagate ST3600002FC?
Ask a Question
Popular Seagate ST3600002FC Manual Pages
Cheetah NS 10K.2 FC Product Manual - Page 7
... Technology® LLC, Cheetah NS 10K.2 FC (Fibre Channel) disk drives. Cheetah NS 10K.2 FC drives support the Fibre Channel Arbitrated Loop and SCSI Fibre Channel Protocol specifications to the extent described in this and other Seagate Fibre Channel drives. B
1
The Fibre Channel Interface Manual (part number 100293070) describes the general Fibre Channel Arbitrated Loop characteristics of...
Cheetah NS 10K.2 FC Product Manual - Page 14
... auto write and read reallocation • Reed-Solomon error correction code • Sealed head and disk assembly (HDA) ...drivers and receivers • Downloadable firmware using the FC-AL interface • Supports SCSI enclosure services via interface connector • 128-deep task set (queue) • Supports up to 32 initiators • Drive selection ID and configuration options are set...
Cheetah NS 10K.2 FC Product Manual - Page 21
... treated as defined in Section 6.2 • Errors caused by the drive, and do not require user intervention. Error rate specified with automatic retries and data correction with this manual assume the following reliability specifications assume correct host and drive operational interface, including all flaws reallocated.
5.1
Error rates
The error rates stated in 1012 bits transferred...
Cheetah NS 10K.2 FC Product Manual - Page 23
... newly inserted drive. Note. The drive's firmware monitors specific attributes for Self-Monitoring Analysis and Reporting Technology. Each monitored attribute has been selected to monitor a specific set , the drive is in ...0, PERF = 0
163 milliseconds
Cheetah NS 10K.2 FC Product Manual, Rev. This technology is intended to enable or disable the S.M.A.R.T.
with the RTZ command resets the timer....
Cheetah NS 10K.2 FC Product Manual - Page 24
... limit according to the drive specification. Signals the host if the temperature exceeds a user-specified value. 3. The temperature is preserved through bus resets and power cycles.
The current algorithm implements two temperature trip points. The error code is measured at power-up and then at which to measure the rate. The firmware keeps a running count...
Cheetah NS 10K.2 FC Product Manual - Page 27
... to defect in the self-test results values log. Seagate will pay for a particular drive can also determine remaining warranty using the abort code in handling computer equipment.
Shipping a drive in transit. Seagate does not sanction any third-party repair facilities. Cheetah NS 10K.2 FC Product Manual, Rev. Seagate repair centers may refuse receipt of shipment to the...
Cheetah NS 10K.2 FC Product Manual - Page 46
...
Cheetah NS 10K.2 FC Product Manual, Rev. However, the drive does not report any unrecovered errors.
The recovery time limit only starts counting when the drive is executing error recovery and it restarts on control of multiple steps, where a step is not counted against the recovery time limit.
B The drive firmware error recovery algorithms consists of 11 levels...
Cheetah NS 10K.2 FC Product Manual - Page 54
... Clear task set Abort task set
Supported No Yes Yes Yes Yes
9.1.3
Fibre Channel task management responses
Table 8 lists the FC SCSI FCP response codes returned for task management functions supported. Table 8: FC SCSI FCP response codes
Function name Function complete Function not supported Function reject
Response code 00 04 05
48
Cheetah NS 10K.2 FC Product Manual, Rev...
Cheetah NS 10K.2 FC Product Manual - Page 60
...Date code page (C1h)
Y
Jumper settings page (C2h)
Y
Device Behavior page (C3h)
Y
Mode select (same pages as Mode Sense command shown below) [3]
Y
Reserve
N
3rd party reserved
N
Extent reservation
Y
Release
N
Copy
Y
Mode sense
Y
Unit attention page (00h)
Y
Error recovery page (01h)
Y
Disconnect/reconnect control (page 02h)
Y
Format page (03h)
Y
Rigid disk drive geometry...
Cheetah NS 10K.2 FC Product Manual - Page 64
... actual year).
** SCSI Revision support. The drive maintains four sets of the product firmware release number. These default values can be changed by downloading a complete set up new current and saved values, where the values are stored into the flash E-PROM. An attempt to do so results in the Fibre Channel Interface Manual.
9.3.1
Inquiry data
Table...
Cheetah NS 10K.2 FC Product Manual - Page 65
... SCSI implementation (see the Fibre Channel Interface Manual ). indicates if default value is 00h which of the data bytes returned by downloading new firmware into the saved values storage location on reset, hard reset, or Bus Device Reset message.
4. On standard OEM drives, the saved values are installed from the default values list and stored...
Cheetah NS 10K.2 FC Product Manual - Page 82
USA/Canada/Latin America support services
For an extensive list of telephone numbers to technical support, presales and warranty service in USA/ Canada/Latin America, including business hours, go to the "Contact Us" page on www.seagate.com. Have your serial number and model or part number available.
Resellers or end users of drive products should contact their place...
Cheetah NS 10K.2 FC Product Manual - Page 84
... drive ID/option select headers 43
drive mounting 37, 44
drive orientation 43 drive select 65 driver signals 72 drivers and receivers 8 dual port support 53
E
electrical description of connector 65 signal characteristics 71 specifications 23
electromagnetic compatibility 3 electromagnetic susceptibility 36
EMI requirements 3 enable bypass
port A 68 port B 68 signal 68 state 16 Enclosure Services...
Cheetah NS 10K.2 FC Product Manual - Page 85
... status 63
Intermix 49, 52
internal data rate 11 internal defects/errors 39 internal drive characteristics 11 IRAW 42
J
J1 connector 43 Jumper settings page command 54 jumpers 43
L
latency average rotational 11
LBdata 56 LED driver signals 72 Link Service Reject (LS_RJT) 47 link services supported 47 Lock-unlock-cache command 56 Log select command 56 Log sense...
Cheetah NS 10K.2 FC Product Manual - Page 87
...
diagram 73 receivers 66 recommended mounting 34 Recoverable Errors 15 recovered media data 15 reference
documents 5 Regenerate command 57 Register FC-4 Types (RFT_ID) 47 Relative address command 55 relative humidity 32 Release command 54 Released (10) command 57 reliability 9
specifications 15 reliability and service 16 repair and return information 21 reporting actual retry count...
Seagate ST3600002FC Reviews
We have not received any reviews for Seagate yet.