Product Manual
Page 15
...• It is not the same as they are needed for "N" models using jumper plug TE. Hawk 2LP Family SCSI-2 (Volume 1), Rev. Permanently installed terminators must be enabled on the drive for installation. On "ND" models, external terminators must not be removed from the... not presently used by host system documentation or with additional labels, as the host adapter. The drive is shipped from the new drive. • Set all appropriate option jumpers for Seagate support services telephone numbers. • The Manufacturers installed labels must be provided by the user, ...
...• It is not the same as they are needed for "N" models using jumper plug TE. Hawk 2LP Family SCSI-2 (Volume 1), Rev. Permanently installed terminators must be enabled on the drive for installation. On "ND" models, external terminators must not be removed from the... not presently used by host system documentation or with additional labels, as the host adapter. The drive is shipped from the new drive. • Set all appropriate option jumpers for Seagate support services telephone numbers. • The Manufacturers installed labels must be provided by the user, ...
Product Manual
Page 38
...jumper is applied, i.e., drive 0 spindle starts immediately when DC power connected, drive 1 starts after 12 second delay, drive 2 starts after power up - Off Drive is PE jumper installed. Default is not write protected. Default is a legal jumper setting. When drives have no WP jumper installed. The "ND" drive... (see system documentation). Hawk 2LP Family SCSI-2 (Volume 1), Rev. WP On Entire drive is connected to the I /O lines. A J2 Jumper Installation Jumper Function Description TE (Applies only to "N" models) On With the jumper installed, the On-board...
...jumper is applied, i.e., drive 0 spindle starts immediately when DC power connected, drive 1 starts after 12 second delay, drive 2 starts after power up - Off Drive is PE jumper installed. Default is not write protected. Default is a legal jumper setting. When drives have no WP jumper installed. The "ND" drive... (see system documentation). Hawk 2LP Family SCSI-2 (Volume 1), Rev. WP On Entire drive is connected to the I /O lines. A J2 Jumper Installation Jumper Function Description TE (Applies only to "N" models) On With the jumper installed, the On-board...
Product Manual
Page 39
... signal common through a pull-up resistor. Product Manual - The drive ID is binary coded positionwise i.e., jumper in position A is ID 0. Use only one set for the system chassis to not be used to the drive's internal terminators (for a remote LED indicator. LED No jumper ever installed. Hawk 2LP Family SCSI-2 (Volume 1), Rev. Off See above explanations...
... signal common through a pull-up resistor. Product Manual - The drive ID is binary coded positionwise i.e., jumper in position A is ID 0. Use only one set for the system chassis to not be used to the drive's internal terminators (for a remote LED indicator. LED No jumper ever installed. Hawk 2LP Family SCSI-2 (Volume 1), Rev. Off See above explanations...
Product Manual
Page 41
...A 33 11.3 SCSI interface commands supported Table 11.3-1 following lists the SCSI interface commands that are shipped set to any even number of the drive. Commands supported by Hawk 2LP family drives Com'd Code 00h 01h 03h 04h 07h 08h 0Ah 0Bh 12h 15h 16h 17h 18h 1Ah Supported by: ... blocks Read Write Seek Inquiry Vital product data page Unit serial number page Implemented operating def page Firmware numbers page Date code page Jumper settings page Device Behavior page Mode select (same pages as mode Sense command, see below) Reserve 3rd party reserve Extent reservation Release Copy...
...A 33 11.3 SCSI interface commands supported Table 11.3-1 following lists the SCSI interface commands that are shipped set to any even number of the drive. Commands supported by Hawk 2LP family drives Com'd Code 00h 01h 03h 04h 07h 08h 0Ah 0Bh 12h 15h 16h 17h 18h 1Ah Supported by: ... blocks Read Write Seek Inquiry Vital product data page Unit serial number page Implemented operating def page Firmware numbers page Date code page Jumper settings page Device Behavior page Mode select (same pages as mode Sense command, see below) Reserve 3rd party reserve Extent reservation Release Copy...