SanDisk SDCFRX4-4096-902 - Extreme IV CompactFlash Support and Manuals
Get Help and Manuals for this SanDisk item
This item is in your list!
View All Support Options Below
Free SanDisk SDCFRX4-4096-902 manuals!
Problems with SanDisk SDCFRX4-4096-902?
Ask a Question
Free SanDisk SDCFRX4-4096-902 manuals!
Problems with SanDisk SDCFRX4-4096-902?
Ask a Question
Popular SanDisk SDCFRX4-4096-902 Manual Pages
Product Manual - Page 28
Interface Description
SanDisk CompactFlash Card OEM Product Manual
3.3.3
Power Up/Power Down Timing
The timing specification in Table 3-9 was defined to permit peripheral cards to perform powerup initialization.
Table 3-9 Power Up/Power Down Timing
Item
Value
CE Signal Levela
CE Setup Time CE Setup Time CE Recover Time VCC Rising Timeb VCC Falling Timeb Reset Width...
Product Manual - Page 29
SanDisk CompactFlash Card OEM Product Manual
Interface Description
Figure 3-2 Power Up/Power Down Timing for all types of memory.
Skews and delays from the system driver/receiver to the card must be accounted for by pull-up resistor on card (if present)
tpf
VCC Min.
Table 3-10 Common Memory Read Timing Specification
Speed Version Item...
Product Manual - Page 36
... IORD-/IOWR- data setup (min.)
t6
IORD- This means a host implementation may lengthen either or both t2 or t2i to ensure that the data bus is no longer driven by the device (tri-state).
02/07, Rev. 12.0
3-18
© 2007 SanDisk Corporation Interface Description
SanDisk CompactFlash Card OEM Product Manual
Figure 3-7 Register Transfer...
Product Manual - Page 38
...Description
SanDisk CompactFlash Card OEM Product Manual
The PIO data transfer parameters are defined in the Card Information Structure (CIS).
A device imple mentation shall support any legal host implementation. b. setup
(...value reported in the system.
02/07, Rev. 12.0
3-20
© 2007 SanDisk Corporation Table 3-16 PIO Data Transfer to IORD-/IOWR- t0 is the minimum total...
Product Manual - Page 47
... at off set 1. Therefore, if the regis ters are not supported. However, repeated alternating...A10 A4 A3 A2 A1 A0 Offset
-OE=0
-WE=0
1
0
X
0 0 0
0
0
Even RD Dataa
Even WR Dataa
1
0
X
0 0 0
1
1
Error Registerb
Featuresb
1
0
X
0 0 1
0
2
Sector Count
Sector Count
1
0
X
0 0 1
1
3
Sector No. SanDisk CompactFlash Card OEM Product Manual
ATA Register Set...
Product Manual - Page 49
... or cannot be transferred in bit 0 of a general error.
4.5.3
Feature Register (Address-1F1[171]; D6
UNC
Set when an uncorrectable error is detected.
If the value in case of the Status Register. Bit
Name
Description
D7
BBK
Set when a bad block is encountered. SanDisk CompactFlash Card OEM Product Manual
ATA Register Set and Protocol
Table 4-6 Data Register
Data...
Product Manual - Page 51
... when the previous command has ended in the Error Register contain additional information describing the error.
4.5.10 Device Control Register (Address-3F6[376];
Reading the Status Register clears a pending interrupt while reading the Auxiliary Status Register does not. SanDisk CompactFlash Card OEM Product Manual
ATA Register Set and Protocol
4.5.9
Status & Alternate Status Registers...
Product Manual - Page 59
...word not supported Capabilities: DMA Supported (bit 8), LBA supported (bit 9) Reserved
© 2007 SanDisk Corporation
5-5...Data Field Type Information General configuration bit-significant ...Firmware revision in ASCII (Rev M.ms) set by code Big Endian Byte Order in Word Model number in ASCII (left justified) Big Endian Byte Order in Word Maximum No.
SanDisk CompactFlash Card OEM Product Manual...
Product Manual - Page 64
...
Indication
0
0
SMART feature set not supported
1
1
Security Mode feature set supported
2
0
Removable Media feature set not supported
3
1
Power Management feature set supported
4
0
Packet Command feature set not supported
5
1
Write cache supported
6
1
Look-ahead supported
7
0
Release Interrupt not supported
8
0
Service Interrupt not supported
9
0
Device Reset command...
Product Manual - Page 65
... Transfer Modes Supported.
© 2007 SanDisk Corporation
5-11
Rev. 12.0, 02/07
Table 5-11 Word 85 Description
Bit
Setting
Indication
0
0
SMART feature set not enabled
1
1
Security Mode feature set enabled via the Security Set Password command
2
0
Removable Media feature set not supported
3
1
Power Management feature set supported
4
0
Packet Command feature set not enabled...
Product Manual - Page 70
... each sector. Disk errors encountered during Read Multiple commands are generated when DRQ is still set at the beginning of the transfer is programmed by a Set Multiple, command.
The...an Aborted Command error. If the number of the block that the number of blocks or the block count) requested. ATA Command Description
SanDisk CompactFlash Card OEM Product Manual
5.1.11
Read ...
Product Manual - Page 73
.../erase failed
5.1.17
Seek-7XH
This command is returned to the host in the Error Register. SanDisk CompactFlash Card OEM Product Manual
ATA Command Description
Table 5-24 defines the valid extended error codes for the CompactFlash Memory Card Series product. The extended error code is effectively a NOP command to the card following the command that returned an...
Product Manual - Page 74
...feature command is used to CompactFlash Memory cards and are supported.
Disable 8-bit data transfer Accepted for backward compatibility with ... Sector Count register. ATA Command Description
SanDisk CompactFlash Card OEM Product Manual
5.1.18 Set Features-EFH
This command is issued, all features that are not part of the ATA Specification. Table 5-26 Set Features
Bit
7
6
5
4
3...
Product Manual - Page 103
... 16 16 16 16 16 16 16 16 16 16 16 16 16
No. Part Number SDCFJ-128-388 SDCFJ-256-388 SDCFJ-512-388 SDCFJ-1024-388 SDCFJ-2048-388 SDCFJ-4096-388 SDCFH-1024-388 SDCFH-2048-388 SDCFH-4096-388 SDCFH-8192-388 SDCFH-16384-388 SDCFX3-2048-388 SDCFX3...
Product Manual - Page 106
... gives you specific rights and you may , at its customers, even if such product is not covered under warranty, but is found to be not covered by the above provisions, then the product will be returned to state.
02/07, Rev. 12.0
B-2
© 2007 SanDisk Corporation SanDisk reserves the right to repair or replace, at...
SanDisk SDCFRX4-4096-902 Reviews
Do you have an experience with the SanDisk SDCFRX4-4096-902 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for SanDisk yet.
Earn 750 points for your review!