Ridgid MS1290LZA Support and Manuals
Get Help and Manuals for this Ridgid item
View All Support Options Below
Free Ridgid MS1290LZA manuals!
Problems with Ridgid MS1290LZA?
Ask a Question
Free Ridgid MS1290LZA manuals!
Problems with Ridgid MS1290LZA?
Ask a Question
Most Recent Ridgid MS1290LZA Questions
Where Is The Serial# Located?
I need to register my saw. I cannot find the serial#. I bought the floor model from Palatine Store
I need to register my saw. I cannot find the serial#. I bought the floor model from Palatine Store
(Posted by khoreis 8 years ago)
Popular Ridgid MS1290LZA Manual Pages
Owners Manual - Page 1
..., trouble-free performance. SLIDING COMPOUND MITER SAW WITH LASER
Double Insulated MS1290LZA
Your miter saw has been engineered and manufactured to our high standard for , it will give you for buying a RIDGID® product.
When properly cared for dependability, ease of operation, and operator safety. Thank you years of injury, the user must read and understand the operator's manual...
Owners Manual - Page 4
..., this manual or addendums. Use of accessories that are included with saw table at an authorized service facility. Make sure blade is tight and not making contact with the accessory.
DOUBLE CHECK ALL SETUPS. DO NOT CUT METALS, CERAMICS OR MASONRY PRODUCTS.
BEFORE MOVING THE SAW, unplug the saw with incorrect size holes. If damaged, have repaired by...
Owners Manual - Page 7
...your nearest AUTHORIZED SERVICE CENTER for repair. SYMBOL
SIGNAL...servicing, use eye protection which , if not avoided, will result in property damage. WARNING:
To avoid serious personal injury, do not use this product until you do not understand the warnings and instructions in the operator's manual, do not attempt to comply with this product. Always use only identical replacement parts...
Owners Manual - Page 11
... used for locking the saw . blade is necessary when rough cutting a dado. It will cut is included with your compound miter saw arm in place. Override (pin pulled completely out) 2. LASER GUIDE
For more accurate cuts, a laser guide is retightened.
Pulling the lever forward will lock the saw . The 0° - 48° position for bevel cuts. lower saw arm.
DEPTH CONTROL KNOB...
Owners Manual - Page 12
... desired position of the saw blade when making bevel or compound cuts. SPINDLE LOCK BUTTON
See Figure 3. SWITCH TRIGGER
See Figure 4. To lock the switch, install a padlock (not included) through the hole in another location.
SLIDING MITER FENCES
The sliding miter fences provided with a click. diameter may require that provides protection from pre-set index points. release...
Owners Manual - Page 15
... shipped with this manual. If any parts are replaced. If shipping has influenced the settings, refer to a workbench or an approved workstand. WARNING:
Do not connect to power supply until assembly is securely mounted to specific procedures explained in this tool. WARNING:
Always make sure the compound miter saw is complete. Failure to a leg stand. If using bolts...
Owners Manual - Page 16
... the saw blade teeth being made in the illustrations. To unlock and raise the saw . ASSEMBLY
NOTE: Many of the illustrations in this manual show points being level with a pencil for use the depth guide: If the saw is facing up.
Release the guide and slowly raise the saw can clearly show only portions of the compound miter saw...
Owners Manual - Page 25
...). Failure to cut . WARNING:
Do not start the compound miter saw on the floor or in serious personal injury. This situation could grab the workpiece if it strikes the miter fence during operation of attachments or accessories not recommended can result in serious personal injury.
The blade could cause an accident resulting in possible serious injury...
Owners Manual - Page 26
... with the miter table set at the back of the saw. When the saw is made with the miter table set at the back of the saw stopping when the full rear position has been reached after each cut.
With the saw off , grasp the saw handle firmly then pull the saw forward until the blade arbor (center of the saw blade) is...
Owners Manual - Page 27
... a roller stand or with a work clamp or a C-clamp to secure the workpiece when possible.
Before turning on the workpiece with the miter table set at the end of workpiece and removing the workpiece from the miter table.
TO MITER CUT / CROSS CUT
See Figures 33 - 34. Miter cross cuts are made .
Grasp the saw blade to...
Owners Manual - Page 28
... desired bevel angle.
Once the saw arm has been set at the desired angle, push the bevel lock lever down to make sure that no problems will occur when the cut is made .
Grasp the saw , perform a dry run of the cut, jamming the blade. Rotate the miter table until the pointer aligns with...
Owners Manual - Page 29
... the bevel setting you change the effect of the two angle settings.
Use the work surface level with the desired angle on the blade at the end of the cut molding, make sure that no problems will seat itself in one of miter and bevel settings are interdependent with thumb then squeeze the switch trigger. A compound miter cut is...
Owners Manual - Page 33
... than any other angle as well. Since it is placed flat on miter table. Miter table set right 31.62° 3. The settings in mind that the settings are very precise and difficult to set.
Save right end of cutting crown molding. In general, compound miter saws do not have angles of a room are at 31.6° either right...
Owners Manual - Page 34
... the wood fence.
Use the chart on the miter table against the miter fence. From the back side of the saw, use a pencil to mark the wood through the wood... miter table.
Make sure the slide lock knob is tightened securely.
Slowly lower the blade into and through the completed support jig.
34
CROWN MOLDING JIG
31.6 22.5
Fig. 46 OPERATION
Bevel Angle Setting
...
Owners Manual - Page 40
...: 01)
40 For the location of this tool is found on a plate attached to provide all relevant information when you , please call or visit.
SLIDING COMPOUND MITER SAW WITH LASER
Double Insulated MS1290LZA
CUSTOMER SERVICE INFORMATION
For parts or service, contact your nearest RIDGID authorized service center. When ordering repair parts, always give the following information:
Model No.
Ridgid MS1290LZA Reviews
We have not received any reviews for Ridgid yet.