Pyle PWD901 Support and Manuals
Get Help and Manuals for this Pyle item
Popular Pyle PWD901 Manual Pages
User Manual - Page 1
... with that may require additional parts and/or labor. While the... Remote Start Module and 2-way Transmitter Instructions Included
SYSTEM MANUAL
STANDARD FEATURES Some of the system's standard features include: • 4-button remote...sensors • Remote Start (optional plug-in module) • Stop & Go Feature • Auto Cold Start Note: Some features may differ between models and between ...
User Manual - Page 2
... alarm is triggered while the optional remote start is engaged, the remote start flashing slowly. This feature can be toggled on door zone setting during installation. During Arming, if the hood or... dome light will turn passive arming on .*
¥ If the alarm was enabled during installation). If triggered by pressing transmitter button 1.) NOTE: Opening the hood/trunk or a door ...
User Manual - Page 3
..., or turning on the ignition key. 3. NOTE: If the system is not set. NOTE: If the optional remote start with the key until either transmitter button 2 is pressed, or the override button ... on /off : 1. NOTE: The optional 2-way transmitter will also relock if selected during installation.
Press button 2 to confirm systems arm/disarm. Press the Valet switch for tamper indication. ...
User Manual - Page 6
... allowing time to the start 3 more times. Turn ignition off.
• The doors will unlock. • The dome light will turn on the remote transmitter.
Press and hold button 2 for Emergency Override, or PIN code override if programmed. To drive the vehicle after a total of the ignition key during installation. Press and hold button...
User Manual - Page 7
...; The vehicle resumes driver control, when the brake pedal is programmed, the engine will shut down , extending its life. Turn on a manual transmission vehicle is performed. The Auto Cold Start feature will continue to run the engine at an operational temperature in manual transmission vehicles.
Installation and safe use of the remote start at the sole risk...
User Manual - Page 8
... Status Ignition
Arm
Disarmed
Off
Disarm
Armed
Off
Remote Valet
Disarmed
Off
Remote Start
Either
Off
Auxiliary 1
Either
Off
Toggle Chirp Mode Either
Off
Immobilizer
Disarmed
Off
Panic Mode
Either
Off
Stop N Go
Disarmed
On
Turbo Timer
Disarmed
On
Manual Trans Mode Disarmed
On
Auto Cold Start
Disarmed
On
Car Locator
Either
Off
Shock Sensor...
User Manual - Page 12
... from moving engine parts such as brake pedals, etc. Make sure the siren cannot be found in a suitable place under dash brace or similar support structure using the ...vehicle starts and idles properly before drilling. VEHICLE SECURITY SYSTEM
Optional Remote Start Module and 2-way Transmitter Instructions Included
INSTALLATION INSTRUCTIONS
BEFORE INSTALLING THIS PRODUCT PLEASE READ THE...
User Manual - Page 13
...anti-grind output (-) 500mA. The starter defeat output is equipped with optional remote start module connected). See Starter Defeat Relay Diagrams and Alarm Programmable Features •... or 4 setting. Brake switch input wire. See Alarm Programmable Features • BLUE/RED WIRE - Trunk trigger (-). For vehicle's with the optional remote start module or the remote start module is ...
User Manual - Page 14
... shows ground when the door is open operation is not installed, the GRAY wire may be optionally set to the optional remote start module using a 3-wire data-link harness. 2-Pin White...4-Pin Connector: Plug-in 2-pin harness. Main ignition output (+). Plug into 2-pin connector from the driver's position. 2-Pin Connector: Plug-in an area easily accessible from 14-pin main harness. •...
User Manual - Page 15
... Connect this wire may used . • BLACK/YELLOW WIRE (large) - This wire provides a ground when the remote start input (-). Ignition 3: For vehicles with the alarm module.
15 Tachometer input. • BLACK/YELLOW WIRE (small) ...leave the GRAY/BLACK wire disconnected, and set dip switch #2 to a solid chassis ground that supplies a pulsed ground output. • BLACK/RED WIRE -
User Manual - Page 16
... presses = Alarm Programming
10 presses = Remote Start Programming • The siren will chirp each time the valet switch is equal to
factory default settings. 3. After entering programming mode, press
...Transmitter Button 1. • The siren will also lock the doors upon rearming. 2. Auto Rearm. Override Mode
No PIN Code PIN Code
...
User Manual - Page 18
..., the wire pulses 10 seconds after the remote start and run cycles. 2. OFF= Ignition 2 operation. Sets the crank delay after remote starting . Selects the operation of the parking light output while the vehicle is shut down . 3.
Cold Start Timer
1 hour
2 hours
4 hours
4. ON= manual transmission. 5. Engine Run Time. When set to 6 minutes after the ignition is connected...
User Manual - Page 19
... wire.This feature allows a faster installation, but may not be installed. General Motors Anti-theft Systems: Many late-model GM vehicles are equipped with the Gray/Black wire (tach input). If the glow plug wire is monitored to make sure the glow plugs have been made, test the remote start by the resistor chip visible...
User Manual - Page 21
...start if the system powered up and in the disarmed state.
If the normally open configuration is selected, Programmable Alarm Feature step 10 must be wired in either configuration, the Starter Defeat relay also provides Anti-Grind protection during remote start... to start using the key. The main unit default setting is normally closed configuration is the recommended installation method....
User Manual - Page 24
Default setting is OFF position (see Remote Start Dip Switches) Starter Test Button RPM Signal LED
64-72.50, 9/04 Rev. 2
24 module side view... used
Black Gray/Black Orange/Violet Pink Black/Red Orange/Gray Yellow/Black
Ground (-) Tachometer input Glow plug input (+/-) Remote start input (-) Remote start output (-) 500mA Hood input (-) Progammable output (-) 500mA
Data-Link Cable (links alarm and...
Pyle PWD901 Reviews
We have not received any reviews for Pyle yet.