Pyle PTA3000 Support and Manuals
Get Help and Manuals for this Pyle item
View All Support Options Below
Free Pyle PTA3000 manuals!
Problems with Pyle PTA3000?
Ask a Question
Free Pyle PTA3000 manuals!
Problems with Pyle PTA3000?
Ask a Question
Most Recent Pyle PTA3000 Questions
Hello A Need The Service Manual For Pta3000 A Need Replacement Some Parts
a need 1 zener diode and 8 power transistor
a need 1 zener diode and 8 power transistor
(Posted by gedjcolima 8 years ago)
My Right Side Shows Falt
(Posted by jwashington 9 years ago)
Pyle PTA3000 Videos
prueba amplificador pyle pro pta3000 luisimprezza forocoches.
Duration: :59
Total Views: 885
Duration: :59
Total Views: 885
Popular Pyle PTA3000 Manual Pages
PTA3000 Manual 1 - Page 2
... for further warnings. No user serviceable parts inside. Do not use attachments/accessories provided by the manufacture. Clean only with a third grounding plug. A polarized plug has two blades with manufacture's instructions.
8.
Read these instructions.
2. CAUTION: To reduce the risk of electrical shock DO NOT OPEN! Follow all warnings.
4. Install in the literature accompanying the...
PTA3000 Manual 1 - Page 3
...support should be provided.
17. Unplug this amplification system in susceptibility to the ear canals or over .
13. If this product is used, use caution when moving the cart/apparatus combination to qualified service...limits as set forth above permissible limits could result in some hearing if exposed to high sound pressure levels, it is in operation.
2 12. Servicing is ...
PTA3000 Manual 1 - Page 4
... cut ) filter for durability in commercial installations and provide the quality performance required in the location where it is designed to the proper OUTPUT connectors, reviewing carefully the impedance and phase considerations. It covers all packing materials. The amplifiers employ mammoth toroidal power transformers and offer impressive specifications and features not found , notify...
PTA3000 Manual 1 - Page 5
...to power up any new installing at this setting to protect the system ...RMS.
(4) OVERLOAD LEDS (CLIP) These indicators illuminate when the associated channel has been overloaded.
(5) FAULT LEDS (FAULT) These indicators illuminate when the amplifier just turned on the mains power to adjust the input gain of each channel of the power amplifier will remain dark as overheat or circuit problem...
PTA3000 Manual 1 - Page 6
... the colored markings identifying the terminals in your safety. The use a qualified electrician to install any equipment. For each channel, and the black binding posts are chassis ground. The ...prevent the risk of continuously supporting at least a #14 AWG wire size. For BRIDGE mode operation, only the red binding posts are in parallel and the speaker connection cables can be used and...
PTA3000 Manual 1 - Page 7
...in what is a conventional push-push type, requiring a small "tool" to use this manual before attempting to activate. This circuitry will be covered later in normal usage. Pins 1-...before using.
(10) MODE SWITCH This switch is part of this case, the input becomes unbalanced with a jumper on pins 1+ and 2+.
It is connected to the ground terminal.
6 An additional unique ...
PTA3000 Manual 1 - Page 8
... designed features that enhance the response of over-excursion. INDUSTRIAL AND COMMERCIAL INSTALLATIONS For commercial and other installation where sustained high-power operation is required, the amplifiers should be patched ...in the stack since each channel will normally stay at 150 Hz and cannot be connected to be patched with single conductor shielded cables.
(17) HIGH OUT JACKS Again...
PTA3000 Manual 1 - Page 9
...be located at low power levels.
8 As a general rule, the cooler electronic equipment is desirable that you have severe cooling problems, even at the top of sensitive equipment by the LEDs on both channels going dark. In most home and studio requirements will... circuitry will prevent possible overheating of an equipment stack. It is operated, the longer its useful service life.
PTA3000 Manual 1 - Page 12
SPECIFICATIONS
RATED OUTPUT POWER: Stereo mode (EIA both channels driven) 4 Ohms EIA, 1 kHz, 1% THD 8 Ohms EIA, 1 kHz, 1% THD Bridge mode, mono 8 Ohms EIA, 1 kHz, 1% THD
HUM & NOISE: Stereo mode, below rated output power, 4 ohms
300W RMS/chan 400W RMS/chan 500W RMS/chan 600W RMS/chan 700W RMS/chan 800W RMS/chan 900W RMS/chan 1000W RMS/chan 150W RMS... 300
FEATURE SET: ALL Models (++indicates each...
Pyle PTA3000 Reviews
We have not received any reviews for Pyle yet.