Pyle PTA3000 Support Question
Pyle PTA3000 Support Question
Find answers below for this question about Pyle PTA3000.Need a Pyle PTA3000 manual? We have 1 online manual for this item!
Question posted by gedjcolima on June 5th, 2015
Hello A Need The Service Manual For Pta3000 A Need Replacement Some Parts
a need 1 zener diode and 8 power transistor
Current Answers
Related Pyle PTA3000 Manual Pages
PTA3000 Manual 1 - Page 2
... (servicing) instructions in accordance with manufacture's instructions.
8. No user serviceable parts inside...does not fit into your safety.
Protect the power cord from being walked on this apparatus near ...servicing to rain or moisture, and objects filled with a third grounding plug. Please read the operating guide for your outlet, consult an electrician for replacement...
PTA3000 Manual 1 - Page 3
...order to prevent permanent hearing loss, if exposure is to be mounted in some hearing if exposed to qualified service personnel. The US Government's Occupational and Health Administration (OSHA) has specified the following permissible noise level exposures...of the type marked on the unit adjacent to a power supply of time.
14. Connect only to the power supply cord.
16. When a cart is in ...
PTA3000 Manual 1 - Page 4
... air and should never be blocked or restricted. Should you ever need to ship the unit back to Sixstar DJ, one of 16...POWER switch to ON, and slowly raise the gain controls to allow adequate connector clearance. Using proven technology gained through years of amplifier design, this manual... Rear mounting ears are two-rackspace units of its service centers, or the dealer: use only the original ...
PTA3000 Manual 1 - Page 5
... of the unit. They determine how loud each channel. FRONT PANEL FEATURES
(1) INPUT GAIN (dB) These controls are operational. It is always a good idea to power up any new installing at this mode selection.
(3) SIGNAL ACTIVITY LEDS (SIGNAL) These indicators illuminate when the associated channel output signal level exceeds 1 V RMS.
(4) OVERLOAD...
PTA3000 Manual 1 - Page 6
...is marked with banana plugs or stripped wires for the intended operating voltage is a standard IEC power connector. Operation at loads of 4 ohms per channel, or 8 ohms BRIDGE mode, is colored... brown must be used and the third wire grounded properly. This is provided for sustained high-power applications.
If the colors of the wires in the mains lead of extension cords should be ...
PTA3000 Manual 1 - Page 7
...alternative, the 1/4" input can also be accomplished using .
(10) MODE SWITCH This switch is part of that shares the same rack with the tip as ground, pin 2 positive input, and pin...speed. are made to this manual before attempting to select STEREO or BRIDGE mode operation. Exercise care when selecting the BRIDGE mode. Always turn power off or the AC mains power source is "automatic" and...
PTA3000 Manual 1 - Page 8
.... The internal fan must then be patched to INPUT of the other installation where sustained high-power operation is required, the amplifiers should be mounted in a standard 19" rack. The IN ...for the corresponding channel. The crossover frequency is fixed at low speed unless sustained high-power operation This type of over-excursion. (14) LOW CUT SWITCH This switch is used ...
PTA3000 Manual 1 - Page 9
...rising from blockage of the amplifier, then steps should be restored relatively quickly, and the power LED on both channels will again be located at the top of the thermal shutdown. ... may cycle continuously between high and low. If cooling is operated, the longer its useful service life. In most home and studio requirements will never cause high-speed fan operation. This will...
PTA3000 Manual 1 - Page 12
...than 0.01% less than 0.01% less than 0.01%
INPUT SENSITIVITY & IMPEDANCE: @ rated output power, 4 ohms Balanced, TRS 1/4" phone jack Balanced, XLR (pin 2 positive) Overall system gain per... 12dB per octave CROSSOVER ++: 150Hz, 4-pole Linkwitz-Riley approximation INPUT++: Electronic balanced; Blue, power AMP PROTECTION: Full short circuit, open circuit; Barrier Strip, XLR, TRS 1/4" (6.3mm) ...
Similar Questions
Pyle Pt720a Schematic
Hello: Can you provide a schematic and/or service manual for the Pyle PT720A?Thank you, Tom
Hello: Can you provide a schematic and/or service manual for the Pyle PT720A?Thank you, Tom
(Posted by aes81 1 year ago)
How Do You Put A Ppre70bt Preamp Into Bt Discovery Mode And What Is Pin Needed?
Setup support
Setup support
(Posted by jcallaci 2 years ago)
I Need To Know If The Pyle Pfa200
is bridgable? And should i connect one negative to speaker and from other channel connect one positi...
is bridgable? And should i connect one negative to speaker and from other channel connect one positi...
(Posted by nevagonnastop87 9 years ago)
Need Help Repair And Plye Pro Pzr 6xa Power Amplifer
i have a short circuit between the 2sa1943 and the voltage regulator...can you help me.
i have a short circuit between the 2sa1943 and the voltage regulator...can you help me.
(Posted by deknight007 9 years ago)
