Pyle PDMT08 Support and Manuals
Popular Pyle PDMT08 Manual Pages
PDMT08 Manual 1 - Page 2
... fuse
(30 seconds max every 15 minutes)
Resistance, Continuity
250Vrms for 15sec max
2. The rules listed below must be carefully followed for safe operation.
1. SAFETY INSTRUCTIONS
This meter has been designed for safe use, but must be operated with high voltages.
3. USE EXTREME CAUTION when working with caution.
PDMT08 Manual 1 - Page 3
...
This symbol adjacent to another symbol, terminal or operating device indicates that the operator must refer to an explanation in the Operating Instructions to avoid personal injury or damage to replace the fuse or batteries.
7. the function switch is in place and fastened securely. CAUTION
This CAUTION symbol indicates a potentially hazardous situation...
PDMT08 Manual 1 - Page 6
...)
m
milli ( volts, amps)
k
kilo (ohms)
ohms
VDC
volts direct current
VAC
volts alternating current
ADC
amps direct current
BAT
Battery test
SPECIFICATIONS
Function
Range
Resolution Accuracy
DC Voltage 200mV 0.1mV
(0.5% reading + 2 digits)
(V DC)
2000mV 1mV
20V
0.01V
6
PDMT08 Manual 1 - Page 7
...;(1.2% reading + 10 digits (50/60Hz) (1.0% reading + 2 digits)
(1.2% reading + 2 digits) (2.0% reading + 2 digits) (0.8% reading + 2 digits)
(1.0% reading + 2 digits) (1.0% reading + 2 digits)
NOTE: Accuracy specifications consist of two elements:
7
PDMT08 Manual 1 - Page 8
... 30 9V (6mA); 1.5V (100mA) >1MΩ 45Hz to 450Hz 200mV 3 ½ digit, 2000 count LCD, 1.1" digits "1" is displayed Automatic (no indication for positive
8 SPECIFICATIONS
Diode Test
Continuity Check
Battery Test current Input Impedance ACV Bandwidth DCA voltage drop Display Overrange indication Polarity
Test current of the measurement circuit.
...
PDMT08 Manual 1 - Page 10
...the screw using a Phillips
head screwdriver. 3. Put the battery door back in place and fastened securely.
BATTERY INSTALLATION
WARNING: To avoid electric shock, disconnect the test leads from the meter. 2.
Insert the battery into battery ...Disconnect the test leads from any source of electrocution. OPERATING INSTRUCTIONS
WARNING: Risk of voltage before removing the battery door. 1.
PDMT08 Manual 1 - Page 11
... display during a measurement, the value exceeds the range you have selected. Large voltage surges may show a random, changing reading. Change to the highest V DC position.
2. Set the function switch to a higher range. 1.ALWAYS turn the function switch to the OFF position when the meter is caused by the high-input sensitivity...
PDMT08 Manual 1 - Page 12
..., the reading may not be long enough to obtain a higher resolution reading. Reset the function switch to successively lower V DC positions to contact the live parts inside some 240V outlets for appliances because the contacts are touching the metal contacts inside the outlet before the value. If the polarity is reversed...
PDMT08 Manual 1 - Page 13
Set the function switch to the meter and/or the test leads.
1. The display will indicate the proper decimal point and value. Insert the black test ...
PDMT08 Manual 1 - Page 14
For current measurements up to 200mA DC, set the function switch to the 10A range and insert the red test lead banana plug into the (mA) jack... successively lower mA DC positions to the circuit.
7. Remove power from the circuit under test, then open up to 10A DC, set the function switch to the negative side of the circuit.
6. Touch the red test probe tip to measure current.
5. Read the...
PDMT08 Manual 1 - Page 15
... the test probe tips across the circuit or part under test. Remove the batteries and unplug the line cords. 1. Set the function switch to the lowest position... and discharge all capacitors before taking any anticipated resistance. Read the resistance in the display and then set the function switch to the highest position. 2. The display will not interfere with the...
PDMT08 Manual 1 - Page 16
Set the function switch to the / •))) position
3. DIODE TEST
1. Turn the rotary switch to the
position.
2. Touch the test probe tips to the circuit or ...
PDMT08 Manual 1 - Page 18
...BAT" will appear in place and fastened securely.
Follow instructions for installing batteries. REPLACING THE FUSES WARNING: To avoid electric shock, disconnect ...REPLACING THE BATTERIES
WARNING: To avoid electric shock, disconnect the test leads from any source of voltage before removing the fuse door.
1. The batteries should be replaced. 2. See the Battery Installation section of this manual...
PDMT08 Manual 1 - Page 19
4. Insert the screw and tighten it securely. Put the fuse door back in place and fastened securely.
19 WARNING: To avoid electric shock, do not operate your meter until the fuse door is in place. Always use a fuse of the proper size and value (0.5A/250V
fast blow for the 200mA range, 10A/250V fast blow for the 10A range). 6. Install the new fuse into the holder. 5.
Pyle PDMT08 Reviews
Do you have an experience with the Pyle PDMT08 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Pyle yet.
Earn 750 points for your review!