ProForm Sys 2 Support and Manuals
Get Help and Manuals for this ProForm item
View All Support Options Below
Free ProForm Sys 2 manuals!
Problems with ProForm Sys 2?
Ask a Question
Free ProForm Sys 2 manuals!
Problems with ProForm Sys 2?
Ask a Question
Popular ProForm Sys 2 Manual Pages
Owners Manual - Page 1
...immediate assistance, free of charge to providing you . al carefully before using this
manual for future reference. PF832220 Serial No.
TO AVOID UNNECESSARY DELAYS, PLEASE CALL DIRECT ...TOLL-FREE CUSTOMER HOT LINE. MST
CAUTION! Save this equipment. ?i?O•FORM'
ModelNo.
I
OWNER'S MANUAL CUSTOMER HOT LINE:
1-800-999-3756
Mon.-Fri., 6 a.m.-6 p.m. Serial Number Decal
QUESTIONS? If...
Owners Manual - Page 2
... are under tension. Replace any exercise program, consult your hands away from this owner's manual.
2. To prevent damage to tip.
5. This is used. Keep your physician.
WARNING: Before beginning this equipment. lems. Read all parts each time this equipment. PROFORM assumes no responsibility for foot protection. Inspect and tighten all instructions before using . Always...
Owners Manual - Page 3
... specific results you , please note the product model number and serial number before using the PROFORM...the PROFORM SYSTEM 2 will help us assist you want. until 6 p.m. To help you to let you have additional questions, please call our Customer Service ... decal). SYSTEM 2. The model number is to the PROFORM SYSTEM 2 (see the front cover of this manual carefully before calling. Before ...
Owners Manual - Page 4
...23) so that all -parts in the Frame (11) as shown.
Tap the two 1/2" Brass Bushings (9) into the ends of the packing materials.
1. Press the two Butterfly Support Endcaps (52) into ...through the Stabilizer. Tap a Hat Axle Cap onto the other end of the Press Arm Axle (43). Place all parts are toward the floor.
Attach the Frame (11) to the Frame 2
(11) with two 3/8" Lock Washers ...
Owners Manual - Page 5
... Nylock Nut (1).
4. Make sure that the Weight Cable is flush with a Spacer (53) on the side of the indicated Weight Guide (19) as shown. Attach another Pulley (10). Grease r -.1
10
1
47
45
47 L.-.
5
2
.„ ,
&#...of the Butterfly Support (49). Lay the end of the Weight Cable (28) over another 3/8" x 2 3/4" Bolt (2) and 3/8" Nylock Nut (1) to the
Butterfly Support in the ...
Owners Manual - Page 6
...
29
Plates (16) with the
collar on the eyelet is in the "I "-Plates just
10
above the Pulley. Find the end of the guide pin on the Frame.
8
2: 1' 17
1 10
30
O
0 O
-10
27
30
A
B
10
r 6 61
17-1
12
...(30) into the lower end of the Cable (see inset C).
Make sure
that end of the guide pin on the Frame. 8.
Slide the 5/16" Washer (51) onto the end of the Cable,...
Owners Manual - Page 7
...x 3/4" Bolts (8) and 1/4" Lock Washers (7).
13. Attach the Butterfly Seat Rail (55) to select the weight setting (see the inset). Attach the end of the Cable to the Press Seat (32) with 3/8" x 1 3/4" ... Nylock Nuts (1). Place the nine Large Weights (56) and the Small Weight (57) between the Weight Guides (19) by tipping the Weights as shown (see ADJUSTMENT).
12. Press the Endcap (37) into the...
Owners Manual - Page 8
...Wet the ends of the Pad Tubes and the
11
insides of the
Tubes. To increase the weight setting, insert one in the weight stack and turn the end of the pin downward. Lift the press seat... be changed from a minimum of 20 pounds, up to the leg lever, remove the chain. The weight setting can be attached as shown with the two cable clips.
8 Always keep one large weight, remove the top...
Owners Manual - Page 9
...and the cable using the adjustment nuts, follow the instructions below. Adjust the length of this equipment regularly.
ATTACHING...non-abrasive detergent. e•
MAINTENANCE AND TROUBLE-SHOOTING
Inspect and tighten all parts of the chain until the cables are... can be attached to the "I "-Plates 9
Replace any worn parts immediately. Tighten the adjustment nuts until they are ...
Owners Manual - Page 10
PART LIST Model No. Specifications...Guide Weight Selector Tube Weight Tube Endcap Chain Stabilizer Stabilizer Endcap Foot Plate 3/8" x 3/4" Bolt Press Arm Weight Cable Long Cable Upper Cable Press Backrest Press Seat Press Seat Rail Leg Lever
Key No. See the back cover of this manual for information about ordering replacement parts... Support Butterfly Backrest 5/16" Washer Butterfly Support ...
Owners Manual - Page 11
PF832220
61 62
52
39
49 48
46 -
64 47
11 53
61
Rev. 10/92
2 2
43 0 -39
39-a. EXPLODED DRAWING Model No. A
45
42
J
S
64-61 6
47 54 7
28
61
1
15 10 61
41
5
4
11
50
5
55
7 1
Or
7
51
12
31
27
20 21
6...60 56
24
7
16 15 19
6
29
I I
32
33
7
7
7
1 8
35 40 39
36 35
37
38
22 3 58
4
59
- 26 25
36 35 34
Specifications are subject to change without notice.
Owners Manual - Page 12
... and other warranty beyond that specifically set forth above is made must be pre-authorized by a PROFORM authorized service center or for products used for a period of ninety (90) days from page 10 of purchase. until 6 p.m. The MODEL NUMBER of the product (PROFORM® SYSTEM 2). 3. This warranty extends only to replacing or repairing, at PROFORM's option, the product at...
ProForm Sys 2 Reviews
We have not received any reviews for ProForm yet.