Poulan XT827ES Support and Manuals
Get Help and Manuals for this Poulan item
View All Support Options Below
Free Poulan XT827ES manuals!
Problems with Poulan XT827ES?
Ask a Question
Free Poulan XT827ES manuals!
Problems with Poulan XT827ES?
Ask a Question
Popular Poulan XT827ES Manual Pages
User Manual - Page 1
IMPORTANT MANUAL
Do Not Throw Away
OWNER'S MANUAL
MODEL NUMBER:
XT827ES
SNOW THROWER
WARNING:
Read the Owner's Manual and follow all Warnings and Safety Instructions.
Failure to do so can result in U.S.A. Always Wear Eye Protection During Operation
429837 09.04.09 SR Printed in serious injury.
User Manual - Page 2
... thrower in contact with a portable container, rather than from a gasoline dispenser nozzle.
2
5. CAUTION: Muffler and other engine parts become extremely hot during operation or while performing an adjustment or repair to a running (except when specifically recommended by the manufacturer for hidden hazards or traffic.
(c) Fill fuel tank outdoors with electric drive motors or...
User Manual - Page 3
... reverse.
13. Maintain or replace safety and instruction labels, as wheel weights, counterweights, or cabs).
15.
SERIAL NUMBER
DATE OF PURCHASE
THE MODEL AND SERIAL NUMBERS WILL BE...13-14
PRODUCT SPECIFICATIONS 3
SERVICE AND ADJUSTMENTS 15-17
CUSTOMER RESPONSIBILITIES 3
STORAGE 18
ASSEMBLY / PRE-OPERATION 4-6
TROUBLESHOOTING 19
OPERATION 7-12
REPAIR PARTS 20-37
MAINTENANCE...
User Manual - Page 11
...quantities that can be used within 30 days to start. See Storage Instructions for a few seconds, remove and read oil level. Rotate choke ...Replace a damaged or worn scraper bar.
receptacle. Wait 5 to the edge of this manual. Use fresh, clean, regular unleaded gasoline with gasoline.
To avoid engine problems, the fuel system should be reversed, providing additional service...
User Manual - Page 13
..., tire sealant may be purchased from the warranty, operator must maintain snow thrower as instructed in the Service and Adjustments section of this manual. TIRES • Maintain proper air pressure in this manual.
• At least once a year, you should replace the spark plug and check belts for loose fasteners.
3.
A new spark plug will need...
User Manual - Page 14
... access to avoid possible engine damage from your expected operating temperature. Install left side wheel may be replaced by original equipment manufacturer (OEM) belts available from running low on dipstick.
10. Pour slowly. For approximate capacity see "PRODUCT SPECIFICATIONS" section of this manual. Use gauge on the gear case. • If lubricant is required...
User Manual - Page 15
... x 1-5/8" capscrew/shear bolts.
Replace belt cover by installing cover and screws and tighten securely. Use only original equipment shear bolts as supplied with your snow thrower with a spacer, shear bolt and hex nut. Wait for all controls and move throttle control to STOP position.
Disengage all moving parts to any service or adjustments:
1. Wait...
User Manual - Page 16
... groove and slide pulley on idler, install new traction drive belt around pulleys. REMOVE ENGINE PULLEY - SEPARATE SNOW THROWER - SERVICE AND ADJUSTMENTS
TO REPLACE BELTS (See Fig. 19)
The ... seated in the Assembly / Pre-Operation section of this manual.
4. NOTE: It is inside belt keeper.
16.
WARNING: Belt replacement requires separation of belts. While separating the auger housing from...
User Manual - Page 17
...service center, which is factory set for pushing or transporting the snow thrower), remove klik pin from axle. ENGINE SPEED
Never tamper with the engine governor, which has proper equipment and experience to a qualified service center. If your engine does not operate properly due to suspected carburetor problems, take your local parts dealer...adjustments. SERVICE AND... When installing wheel,...
User Manual - Page 18
...ENGINE
See engine manual. Acidic gas can attract moisture which allows condensation to form and will cause problems.
• ...storage. Rust and/or dirt in essential fuel system parts such as carburetor, fuel hose, or tank during... Service and Adjustments section of this manual).
3. Inspect and replace belts, if necessary (See "TO REPLACE BELTS" in the Maintenance section of this manual)....
User Manual - Page 19
... discharge chute. 4. Check / replace auger belt. 3. Spark plug wire loose. 2. Dirty or clogged muffler.
1. Reduce speed and width of traction 1. Move choke to spark plug.
9. If vibration remains, contact an authorized service center/department. Auger belt is worn. 3. TROUBLESHOOTING
See appropriate section in need of
adjustment or overhaul.
1. PROBLEM
CAUSE
CORRECTION
Does not...
User Manual - Page 20
MODEL NUMBER XT827ES (96192003401) AUGER HOUSING / IMPELLER ASSEMBLY
5
15 14
4
11 6
12
16
11
13
12 3
11
10
...2 (EXPLODED)
01.07.026-C
NOTE: All component dimensions given in U.S. REPAIR PARTS SNOW THROWER - - inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void...
User Manual - Page 21
REPAIR PARTS SNOW THROWER - - Failure to do so could be hazardous, damage your snow thrower and void your warranty.
21 MODEL NUMBER XT827ES (96192003401) AUGER HOUSING / IMPELLER ASSEMBLY
KEY NO.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17...BOLT
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
User Manual - Page 25
... INDICATED WITH AN * ARE LISTED AS REFERENCE FOR SERVICE PARTS ONLY. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. NOTE: All component dimensions given in U.S. Failure to do so could be hazardous, damage your snow thrower and void your warranty.
25
MODEL NUMBER XT827ES (96192003401) CONTROL PANEL / CHUTE
2 2
*3
1 *7
KEY NO...
User Manual - Page 26
... replacement parts. REPAIR PARTS SNOW THROWER - - MODEL NUMBER XT827ES (96192003401) HANDLES
4
4 3
2
01.08.004-B
3
4
4
3
3
KEY PART NO. NO. DESCRIPTION
1
419798X479 LOOP HANDLE LH
12 3
419799X479 LOOP HANDLE RH
74780524
SCREW 5/16−18 X 1.50
4
751153
NUT 5/16−18
1
KEY NO.
1 2 3 4
PART NO.
419797X479 418313X479 428867 17000616
DESCRIPTION
LOWER TUBE PIVOT SUPPORT...
Poulan XT827ES Reviews
We have not received any reviews for Poulan yet.