Poulan HDF825X Support and Manuals
Get Help and Manuals for this Poulan item
This item is in your list!
View All Support Options Below
Free Poulan HDF825X manuals!
Problems with Poulan HDF825X?
Ask a Question
Free Poulan HDF825X manuals!
Problems with Poulan HDF825X?
Ask a Question
Popular Poulan HDF825X Manual Pages
User Manual - Page 1
IMPORTANT MANUAL
Do Not Throw Away
OPERATOR'S MANUAL
MODEL:
HDF825X
FRONT TINE TILLER
WARNING:
Read this Manual and follow all Warnings and Safety Instructions. ALWAYS WEAR EYE PROTECTION DURING OPERATION Visit our website: www.poulan-pro.com
411044 01.05.07 CL Printed in serious injury. Failure to do so can result in U.S.A.
User Manual - Page 2
...operator's guide instructions for the cause. YOUR SAFETY IS INVOLVED. Never fill fuel tank indoors.
• Replace gasoline cap securely and clean up , transporting, adjusting or making repairs. ... (except where specifically recommended by attempting
to cause cancer, birth defects, or other reproductive harm.
2 If this product contains chemicals known to the State of trouble.
•...
User Manual - Page 3
... and retain this Manual. The instructions will enable you cannot easily remedy, please contact your tiller properly.
OTHER STATES MAY HAVE SIMILAR LAWS. TABLE OF CONTENTS
SAFETY RULES 2 PRODUCT SPECIFICATIONS 3 CUSTOMER RESPONSIBILITIES 3 ASSEMBLY 4-5 OPERATION 6-9 MAINTENANCE SCHEDULE 10
MAINTENANCE 10-12 SERVICE & ADJUSTMENTS 12-14 STORAGE 15 TROUBLESHOOTING 16 WARRANTY 17...
User Manual - Page 4
TOOLS REQUIRED FOR ASSEMBLY
A socket wrench set will make assembly easier. Standard wrench sizes are in this manual, it means when you assemble must be tightened securely. ...16-18
4
ASSEMBLY
Your new tiller has been assembled at the factory with exception of your tiller all parts and hardware you are listed. (1) Utility knife (1) Screwdriver (2) 1/2" wrenches
OPERATOR'S POSITION (See Fig....
User Manual - Page 5
...18X1"
02051
CABLE(S)
TILLER HANDLES
HANDLE PANEL BOLTS
INSTALL DEPTH STAKE ASSEMBLY (See Fig. 3)
• Loosen nut "A".
• Insert stake support between engine bracket halves with handle panel hole and...stake support to skid and discard the screws. Be sure the shorter (1" long) hex bolt is assembled in the Service and Adjustments section of this manual). If it does not, loosen support ...
User Manual - Page 8
... For approx- To avoid engine problems, the fuel system should change oil for easier starting engine.
• To change engine oil, see "PRODUCT SPECIFICATIONS" on its wheels and then ...start of this manual). See Storage Instructions for additional information. Never use gasoline near an open flame.
• Push or pull tiller to point of acids during storage. Replace oil filler plug...
User Manual - Page 9
..., and you leave a row untilled between rows to start , see troubleshooting points. OPERATION
NOTE: If at a high altitude (3000 feet) or... leave the ground in the Service and Adjustments section of this manual. If you are not set properly in order to prevent ...them from the operator.
• Tilling is through trial and error and depends upon the soil condition. (The harder or wetter...
User Manual - Page 11
... • Catch oil in the Operation section of this manual. Keep the engine free of the cartridge. Do not ... to drain oil. • After oil has drained completely, replace oil drain plug
and tighten securely. • Remove oil filler...13)
Service air cleaner cartridge every twenty-five hours, more frequently to clean cartridge. Do not oil cartridge. brush. • Remove blower housing and...
User Manual - Page 12
Replace if damaged.
Water in engine will not require lubrication unless serviced....setting are covered to holes "B" in tine shaft. TRANSMISSION
Your transmission is equipped with automotive type wax. TILLER
TO ADJUST HANDLE HEIGHT (See Fig. 15)
Factory assembly has provided lowest handle height. Handle height will be assembled in "PRODUCT SPECIFICATIONS" on page 3 of this manual...
User Manual - Page 13
...cable to remove slack, without extending spring on cable only enough to service belts.
TO REMOVE BELT GUARD (See Fig. 20)
• Remove... belt guard out and away from inner wire of all belt guides before removing belts.
13 FINAL CHECK "OFF" POSITION
•...push down on end of manual. TINE SHIELD NUT
FIG. 20
TO REPLACE V-BELTS (See Figs. 21 and 22)
Replace V-belts if they have stretched...
User Manual - Page 14
..., CONTACT YOUR NEAREST AUTHORIZED SERVICE CENTER/ DEPARTMENT, WHICH HAS THE PROPER EQUIPMENT AND EXPERIENCE TO MAKE ANY NECESSARY ADJUSTMENTS. REPLACE BELT GUARD
ENGINE
TO ADJUST CARBURETOR
The carburetor has been preset at the factory and adjustment should not be affected by differences in this section of
manual.
BELT REPLACEMENT • Install new forward (inside .
•...
User Manual - Page 15
...replace belts, if necessary (See belt replacement instructions in the Service and Adjustments section of this manual).
• Lubricate as shown in the Maintenance section of oil through spark plug hole into
cylinder. • Pull starter handle slowly several times to distribute
oil. • Replace with gasoline in your gasoline will cause problems... ESSENTIAL FUEL SYSTEM PARTS SUCH AS THE ...
User Manual - Page 16
...fresh gasoline. 8. Clean/replace muffler. 12.
V-belt not correctly adjusted. 3. TROUBLESHOOTING POINTS
PROBLEM Will not start
CAUSE
1. Stale or dirty fuel. 5. Low oil level/dirty oil. 4. Contact an authorized service center/department. Improper carburetor adjustment.
1. Wait for more favorable soil conditions. Check throttle control setting. 3. Bad spark...
User Manual - Page 17
... these items.
2.
This Warranty gives you specific legal rights, and you . This is a limited Warranty within the meaning of the product.
5. Please refer to normal wear of that this product as defined in accordance with the instructions furnished. Exclusions: Excluded from locale to an authorized service dealer. THIS WARRANTY DOES NOT APPLY TO INCIDENTAL...
User Manual - Page 18
... described in this Manual, please contact your local dealer(s). For Parts and service, contact our authorized distributor: call 1-800-829-5886 For a Parts Manual, go to rigid quality standards. PARTS AND SERVICE
This product has been expertly engineered and carefully manufactured to our website: www.poulan-pro.com/support.asp
NOTE:
HOP provides parts and service through its products...
Poulan HDF825X Reviews
Do you have an experience with the Poulan HDF825X that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Poulan yet.
Earn 750 points for your review!