Poulan 1981-10 Support and Manuals
Get Help and Manuals for this Poulan item
View All Support Options Below
Free Poulan 1981-10 manuals!
Problems with Poulan 1981-10?
Ask a Question
Free Poulan 1981-10 manuals!
Problems with Poulan 1981-10?
Ask a Question
Popular Poulan 1981-10 Manual Pages
User Manual - Page 1
Fa
Poutan
Micro XXV
Read Special SAFETY CENTER SPREAD
each time you use your MICRO 25
CHAIN SAW
OPERATOR'S MANUAL
K BEAIRD-POULAN Division EmerSon Electric Co.
/
WEED
EATER
5020 Flournoy-Lucas Road
Shreveport, Louisiana 71109
User Manual - Page 2
...of Cutting Adjusting Carburetor Air Filter Sharpening Chain
& Guide Bar Maint. Starter Rope
PAGE
2 3 4
5 6 7 8-9 10-11 12.13 13
14 15
2
Read ...the handlebar AT ALL TIMES.
3. Manufacturing and Engineering, Beaird-Poulan
Good Firm Grip With Both Hands
\N
2 Good Performance SAFETY...tip up or down and back. Eliminate or 'avoid any part of the saw chain could hit while you take several ...
User Manual - Page 3
...SPECIFICATIONS 10" SAW
ENGINE DISPLACEMENT
2.0 Cu, In. Gasoline Automatic only 12" Control TipTM
Low Profile 3/8 Pitch Chrome Cutters 45 Drive Links
Spark Arresting
14" SAW
2.0 Cu. Oil to cut any material other than wood. Fuel Cap
r---- 7/, Cs)
0
CounterVibe Model
Vibration Mount Low-Kick Chain
Control Tipm.Guide...Gasoline
OILER
Automatic only
GUIDE BAR
10" Control TipTM
CHAIN
...
User Manual - Page 4
Please lift and carry the chain saw .
COUNTERVIBE MODELS
1. PARTS AND TOOLS
Check the box for fuel. For CounterVibe Model, a small adjustable wrench. FOR MIXING FUEL AND ADDING CHAIN ... CounterVibe Bracket. Retighten, if it will need the proper fuel mixture, (see the fueling section of this manual, page 6), and, bar and chain lube or clean SAE 30 oil. If something is missing, please...
User Manual - Page 5
...guide bar is still flat against the side of the saw model. Replace the small bar clamp screw in back.
5. If the chain does not set in easily at the tip, pull the chain forward and let the groove guide...Remove the bar clamp. To install the guide bar as you are cutting. A JUSTING SCR
6. Holding the tip of the bar, setting it down as shown, slide the guide bar behind the clutch drum on...
User Manual - Page 6
...1 gallon of oil may appear under the saw on the guide bar might be damaged.
This will burn out your chain saw.... Remove the bar clamp and bar and chain. or 1/2 pt. (8 oz.) Poulan 32:1 oil with 1 gallon of 95% bar and chain lube and 5% either ...CENTER SPREAD
FREQUENTLY
Do not leave fuel in the bar anc replace the bar, chain, and bar clamp. Remove old fuel...10%. As long as you refuel.
User Manual - Page 7
... throttle the entire time you fueled your chain saw has run the engine at wide open throttle. If saw , push the START/STOP switch to 10 pulls with your right hand while holding trigger at high speed when not in a cut and keep the saw . Now, move away from you with...
User Manual - Page 8
...stopped, the guide bar and ...service other adverse weather conditions.
You need good visibility, so don't cut if the weather is sharp and at least 10...manual. Operate the chain saw . or if you are fatigued, tired, or upset; sical condition and mentally alert. You need both her for safe climbing. Do not start cutting until you have be specifically... and operating instructions found in...
User Manual - Page 9
... shut off oil before setting the saw chain at high...guide bar which occurs when the saw down. Follow manufacturer's sharpening and maintenance instructions...parts of the chain saw in the wood fibers is not contacting anything.
Kickback can lead to your protective gear. Store the saw cool in an area away from Lloyd Tuggle, Senior Vice President, Engineering, Beaird-Poulan...manual.
User Manual - Page 10
... notch. If you know the direction of fall , stop the saw, put it down and GET AWAY QUICKLY. Direction of Fall
Wedge-,
Notch-'
2,"
I Felling Cut
/4
10
NOTCH METHOD
You notch a tree to get the tree to fall . As the tree starts to fall in is free from the direction of fall...
User Manual - Page 11
... or below.
B
First Cut
A
Second Cut
Using a bucking stand, in a log,
the guide bar under pressure, and for branches that are higher, get a professional. Do not turn saw ...undercut. Do not turn the saw upside down from top. Work slowly, watching out for supporting limbs. Make finishing cut overhead. Finish by
cutting up from the top. Keep your footing...
User Manual - Page 12
...screw (3). Position the low speed mixture screw at the proper gasoline/oil ratio (see mixing
instructions), and a screwdriver. If the chain is not squeezed (idle position)
CLOCKWISE
CLOCKWISE
COUNTERCLOCKWISE...the choke knob.
2. The carburetor has been carefully adjusted at the best idle setting, turn the low speed mixture screw counterclockwise until the chain stops. PRELIMINARY: stop...
User Manual - Page 13
...dirt out of operation. Repeat this adjust- Check for proper idle mixture screw setting per instructions in front of a turn counterclockwise at a time until you have power in...turning.
If there is set properly and the chain is oil coated. The filter should be cleaned after every 10 tanks of fuel or every 5 hours of the carburetor. Replace carburetor cover.
13 CLEANING ...
User Manual - Page 15
..., push it counterclockwise. If rope is not pulled loose or pinched. Pull out 10" of rope and catch the rope in the
slot in the center of the pulley...Repairing the recoil starter rope requires a certain degree of the rope and pull it .
3. SAFETY CENTER SPREAD -.1FREQUENTLY-1,',:t:
1. Pull the gas line off the fan housing. Move away from the fan housing, replace the cap and set...
User Manual - Page 16
... the name of the unit b. For replacement parts, have available the following information: a. Box 9329 Shreveport, Louisiana 71129
64567 10/81 Parts and repair service are placed on the market also. As with rigid quality standards. FOR SERVICE OR REPLACEMENT PARTS. 1. Model number c. NOTE: Beaird-Poulan/Weed Eater provides parts and service through its authorized distributors and dealers...
Poulan 1981-10 Reviews
We have not received any reviews for Poulan yet.