Polk Audio PA660.4 Support and Manuals
Get Help and Manuals for this Polk Audio item
View All Support Options Below
Free Polk Audio PA660.4 manuals!
Problems with Polk Audio PA660.4?
Ask a Question
Free Polk Audio PA660.4 manuals!
Problems with Polk Audio PA660.4?
Ask a Question
Most Recent Polk Audio PA660.4 Questions
Protection Light
How do I turn off or get out of protection so I can fix it
How do I turn off or get out of protection so I can fix it
(Posted by TripleOGbrown 6 years ago)
Popular Polk Audio PA660.4 Manual Pages
PA880 Owner's Manual - Page 2
...PANEL LAYOUTS 5-8
Input Plate 5-7 Output Plate 6-8 SPEAKER LEVEL HARNESSES 8 AMPLIFIER SETTINGS 8-9 Signal Input and Output Configurations 8 Phase Switches 8 Auxiliary Output Configurations 9 Low-Pass Crossover 9 Remote Bass Operation 9 High-Pass Crossover 9 AMPLIFIER WIRING 9-12 Power Connections for the Polk Audio PA330, PA660 and PA880 9 Speaker Wiring Diagram PA330/PA660/PA880 10...
PA880 Owner's Manual - Page 3
...PA660-340 Watt: four-channel Class A/B amplifier with built-in its products. Keep these tools are capable of playing at extremely high volume levels, which could cause serious or permanent hearing damage. Speaker Level Input-Connect speaker output from a source unit, preamplifier, or equalizer. 4. Line Level Inputs-Accepts line level input from factory radio to perform the installation...
PA880 Owner's Manual - Page 4
... fault condition in amplifier, also lights briefly during muting phase of turn-on when needed ; Power Connections-accepts up to 12 AWG speaker wire. 2. 1 ATC Fuse-protects the amplifier from radio and turn amplifier on /off after 1 minute without signal. 7. 2 Ch / 4 Ch Switch-allows all rights reserved
7 Speaker Level Input-connect speaker output from the rear channels of phase...
PA880 Owner's Manual - Page 5
... bass port provides easy remote access to 12 AWG speaker wire. 2. 2 ATC Fuses-protects the amplifier from 50Hz to your next Polk Audio PA amplifier in phase with either grounded or BTL speaker level outputs v i
SPEAKER LEVEL CONNECTIONS
WIRE COLOR Black
INPUT CONNECTION Ground
White White/Black
+ Left Front channel - Low-Pass Crossover /…i VÀœÃÃ...
PA880 Owner's Manual - Page 6
...mode
bridged
Bridging
For bridging into a single speaker load, the Polk Audio PA330 has the ability to bridge the front or rear channels together. Speaker Wiring Diagram PA330 The Polk Audio PA330 amplifier offers two positive and two negative output terminals for ease of connecting the speakers to the amplifier. The mono low frequency speaker would be run in line passive VÀœ...
PA880 Owner's Manual - Page 7
Speaker Wiring Diagram PA880 The Polk Audio PA880 amplifier offers two positive and two negative output terminals for ease of this guide. Single 2 Ohm speaker or 2 ea. Refer to the Phase Switch section of connecting the speakers to the amplifier. Always mount the amplifier in a place that is not covered under warranty. Do not mount any fashion.
General Precautions and Installation Tips ...
PA880 Owner's Manual - Page 8
... for correct wiring instructions. Check power wire's integrity and check for optimum front/rear balance. Be sure to run Line levels and power and speaker wires away from the amplifier location to the Amplifier Settings and Speaker Wiring Diagrams sections of this guide for amplifier and improve ventilation as needed .
© 2010 Polk Audio-all connections and settings are correct...
PA880 Owner's Manual - Page 9
... at amplifier is smaller than recommended.
Loose or poor audio input
Loose power connections
Distorted output Amplifier level sensitivity set too high exceeding maximum capability of this manual for detailed instructions Readjust crossovers. Check power wires and ground connections and repair or replace as needed . Reset crossovers.
Battery fuse blowing
Short in power...
Polk Audio PA660.4 Reviews
We have not received any reviews for Polk Audio yet.