Pioneer PRS-D1200M - Premier Amplifier Support and Manuals
Get Help and Manuals for this Pioneer item
View All Support Options Below
Free Pioneer PRS-D1200M manuals!
Problems with Pioneer PRS-D1200M?
Ask a Question
Free Pioneer PRS-D1200M manuals!
Problems with Pioneer PRS-D1200M?
Ask a Question
Popular Pioneer PRS-D1200M Manual Pages
Owner's Manual - Page 2
...of enjoyment. Please read all instructions and WARNINGS in this PIONEER product. CUSTOMER SUPPORT DIVISION P.O. After-sales service for Pioneer products
Please contact the dealer or distributor from where you purchased the product for its aftersales service (including warranty conditions) or any questions, contact your nearest Pioneer authorized dealer or installation specialist. In case the...
Owner's Manual - Page 3
... the problem, then replace the fuse with wet hands. In addition, the amplifier surface and the surface of this product, output is a mono amplifier. Detect the cause and solve the problem.
• Contact the dealer if you cannot detect the cause. • To prevent an electric shock or short-circuit
during connection and installation, be...
Owner's Manual - Page 4
... a 4 mm hexagonal wrench and remove the top cover.
Power Indicator
The power indicator lights when the power is on . Top Cover
Before setting up the unit, unfasten the screws with your car stereo, change the BFC switch using a small standard tip screwdriver.
For instruction of the unit. Setting the Unit
• To adjust the switch, use...
Owner's Manual - Page 5
... an RCA equipped Pioneer car stereo with synthetic impeadance from 1 Ω to less than 2 Ω, slide the switch to the left . bridge), although the POWER MODE switch be may set to the NORMAL...multiple amplifiers. Switch the input switch before turning on the MODE SELECT switch. For connection instructions, see the "Using the Speaker Input" section. ENGLISH
ESPAÑOL DEUTSCH FRANÇ...
Owner's Manual - Page 6
... of the head unit and set the gain control of the amplifier to a proper position according to the preout maximum output level of the unit itself and speakers from time to NORMAL.
5 But this function will be improperly set to time, contact the nearest authorized PIONEER Service Station. Setting the Unit
Setting the Gain properly
•...
Owner's Manual - Page 7
... feed power to work when it may go dead. Otherwise the protection circuit may catch fire, emit smoke or become damaged, resulting in the "Connecting the Unit" section. Before installing it where they lie against metal parts.
• Do not route wires where they will always be exceeded, causing overheating.
• Never replace the...
Owner's Manual - Page 8
...INPUT jack connection instructions. This is because the LPF of the amplifier cannot be connected to the system remote control terminal of the amplifier to the power terminal through ...228] (sold separately) Connect to set the input switch. RCA input jack
SYNC OUT/SYNC IN jack See the "Connecting the Speaker Wires" section for speaker connection instructions. System remote control wire (sold...
Owner's Manual - Page 9
... tighten and loosen the terminal screw of the amplifier. System remote control terminal
Power terminal
Terminal screws GND terminal
Ground wire
Battery wire
System remote control wire
WARNING...the battery.
Connect the wires to tighten excessively by observing the status of this amplifier (Power terminal, GND terminal, System remote control terminal).
The battery wire and the ground wire ...
Owner's Manual - Page 10
...amplifier using nippers or a cutter by about 10 mm (3/8 inch) to the amplifier, the power of the speaker wires using the supplied speaker input wire with the terminal screws. It is ...)
2.
Note: • Connect the system remote control wire when the
power of the amplifiers with RCA pin cord, the amplifier power is only turned on when one amplifier is being used. Connecting the Unit...
Owner's Manual - Page 11
... instruction manual for details.
10 Single Amplifier
MODE SELECT switch must Connect to a car stereo. If the synthetic impedance is from 1 Ω to 8 Ω. • The setting of the POWER ...set to MASTER with the MODE SELECT switch.
Improper
4 Ω Speaker
4 Ω Speaker
2 Ω Speaker
2 Ω Speaker
2 Ω Bridged Mode
1 Ω Bridged Mode
Do NOT install...
Owner's Manual - Page 12
... OUT
Connect to 16 Ω. Connecting wire with RCA pin plugs (sold separately). See the "Setting the
Unit" section for both amplifiers.
11
In addition, in the case of 2 Ω to... setting is from 1 Ω to 8 Ω. • The setting of the POWER MODE switch varies according to a car stereo.
The same setting is at least 2 Ω.
• The setting of the POWER MODE...
Owner's Manual - Page 13
...AIS ITALIANO NEDERLANDS
Four Amplifier (Ex. For details, see the "Connection Diagram".
Slide the POWER MODE switch to the HI-CURRENT position if the impedance is from 2 Ω to less... it to the NORMAL position if the impedance is at least 2 Ω.
• The setting of the POWER MODE switch varies according to 16 Ω. Connecting wire with a bridge, check that connections are...
Owner's Manual - Page 14
... with SYNC IN RCA pin plugs (sold separately).
1 Ω to 8 Ω
SYNC IN
• Use speakers having an impedance from 1 Ω to 8 Ω. • The setting of the POWER MODE switch varies according to the speaker impedance. Connecting wire with RCA pin plugs (sold separately).
See the...
Owner's Manual - Page 15
...to come into contact with liquids due to, for installation differs with the car model and installation location. In addition, the amplifier surface and the ...Installation
CAUTION
• Do not install in: -Places where it could injure the driver or passengers if the vehicle stops suddenly. -Places where it may become loose causing the amplifier to shut down.
• Never replace...
Owner's Manual - Page 17
... DEUTSCH FRANÇAIS ITALIANO NEDERLANDS
Specifications
Power source ...14.4 V DC (10.8 V to 15.1 V allowable) Grounding system ...Negative type Current consumption ...39 A (at continuous power, 4 Ω) Average current drawn* ...12 A (4 Ω for one channel)
20 A (2 Ω for one channel) 28 A (1 Ω for one channel) Fuse ...40 A × 2 Dimensions ...301 (W) mm × 57 (H) mm...
Pioneer PRS-D1200M Reviews
We have not received any reviews for Pioneer yet.