Owners Manual
Page 1
... amplifier. One that no parts are behind the panel when drilling a hole for installation of the Deafness Research Foundation. CUSTOMER SERVICE DEPARTMENT P.O. Connect the battery wire directly to the car battery positive terminal (+) and the ground wire to your equipment at a safe level. Detect the cause and solve the problem, then replace the fuse with your volume control at a low setting. • Slowly increase the sound until it there. Publication de Pioneer...
... amplifier. One that no parts are behind the panel when drilling a hole for installation of the Deafness Research Foundation. CUSTOMER SERVICE DEPARTMENT P.O. Connect the battery wire directly to the car battery positive terminal (+) and the ground wire to your equipment at a safe level. Detect the cause and solve the problem, then replace the fuse with your volume control at a low setting. • Slowly increase the sound until it there. Publication de Pioneer...
Owners Manual
Page 2
... other bridge connection. • Install and route the separately sold battery wire, ground wire, speaker wires and the amplifier as far away as follows according to the type of speaker that is connected to the speaker output connector and the car stereo system: LPF/HPF Select Switch LPF (left) OFF (center) HPF (right) Audio frequency range to tap from 0 to the system remote control terminal of the car stereo (SYSTEM REMOTE CONTROL). Power Indicator The power indicator lights when the power is switched on - To protect the wiring...
... other bridge connection. • Install and route the separately sold battery wire, ground wire, speaker wires and the amplifier as far away as follows according to the type of speaker that is connected to the speaker output connector and the car stereo system: LPF/HPF Select Switch LPF (left) OFF (center) HPF (right) Audio frequency range to tap from 0 to the system remote control terminal of the car stereo (SYSTEM REMOTE CONTROL). Power Indicator The power indicator lights when the power is switched on - To protect the wiring...
Owners Manual
Page 3
... high/mid-high. • Remember when bridging an amplifier it is connected, RCA output becomes functional. This will reproduce. Engine Fuse (30 A) compart- GND terminal Power terminal System remote control terminal System remote control wire Ground wire Battery wire Fuse (30 A) Drill a 14 mm Positive terminal hole into the vehicle body. 2. Twist 4. Connect the speaker leads to suit the mode according to the figures shown below to the speaker terminals. • Connect the speaker wires, passing them so they cannot be set up using...
... high/mid-high. • Remember when bridging an amplifier it is connected, RCA output becomes functional. This will reproduce. Engine Fuse (30 A) compart- GND terminal Power terminal System remote control terminal System remote control wire Ground wire Battery wire Fuse (30 A) Drill a 14 mm Positive terminal hole into the vehicle body. 2. Twist 4. Connect the speaker leads to suit the mode according to the figures shown below to the speaker terminals. • Connect the speaker wires, passing them so they cannot be set up using...
Owners Manual
Page 4
...) (Bridge connection: 2 - 8 Ω allowable) Frequency response ...10 - 50,000 Hz (+0 dB, -1 dB) Signal-to-noise ratio ...105 dB (IHF-A network) Distortion ...0.005% (10 W, 1 kHz) Separation ...65 dB (1 kHz) Low pass filter ...Cut off frequency: 80 Hz Cut off slope: -12 dB/oct High pass filter ...Cut off frequency: 80 Hz Cut off slope: -12 dB/oct Bass boost ...Frequency: 60 Hz Gain: 0 - 18 dB Maximum input level/impedance RCA...
...) (Bridge connection: 2 - 8 Ω allowable) Frequency response ...10 - 50,000 Hz (+0 dB, -1 dB) Signal-to-noise ratio ...105 dB (IHF-A network) Distortion ...0.005% (10 W, 1 kHz) Separation ...65 dB (1 kHz) Low pass filter ...Cut off frequency: 80 Hz Cut off slope: -12 dB/oct High pass filter ...Cut off frequency: 80 Hz Cut off slope: -12 dB/oct Bass boost ...Frequency: 60 Hz Gain: 0 - 18 dB Maximum input level/impedance RCA...