Panasonic EYFLA5P Support and Manuals
Get Help and Manuals for this Panasonic item
View All Support Options Below
Free Panasonic EYFLA5P manuals!
Problems with Panasonic EYFLA5P?
Ask a Question
Free Panasonic EYFLA5P manuals!
Problems with Panasonic EYFLA5P?
Ask a Question
Popular Panasonic EYFLA5P Manual Pages
EYFLA4A User Guide - Page 5
... or carrying the tool, set the Forward/Reverse lever to be performed. Contact with specifically designated battery packs. Do ... pack is a Cordless Impact Driver/Wrench and can make exposed metal parts of battery pack may become slightly...Instructions" booklet and the following before use , keep it does not have the power tool repaired before using only identical replacement parts...
EYFLA4A User Guide - Page 6
... pack from falling out. The collar will return to make sure it out from the tool. Pull the bit to its origi-
IV.
EYFLA4A/EYFLA4AR/EYFLA5A/EYFLA5AR
12 mm (15/32")
9 mm - 9.5 mm 6.35 mm (23/64" - 3/8") (1/4")
NOTE: Be sure to attach the rubber ring to or detaching them from the...
EYFLA4A User Guide - Page 8
... when the remote control is operated close to respond, even when the remote control is dirty may not last as long as commercially available batteries.
Replace it with a fresh battery. • The included battery is provided for sample use and may cause the tool to fail to the tool, the battery...
EYFLA4A User Guide - Page 9
... in LED light is released.
4.
The speed increases with retightening within 1 second, the red lamp will not turn on and off when the tool is set the lever to check whether the torque control function was activated. Use of controls or adjustments or performance of the tool during impactmode tightening and...
EYFLA4A User Guide - Page 10
... from the motor's rotational angle during tightening, the load may be charged (or replaced with ambient temperature and battery characteristics.
Battery indication lamp Indicator
Flashing
NOTE: •...The torque control function will not operate until the battery pack has been charged (or replaced with bolt diameter. • Torque coefficient (indicated by the bolt manufacturer), grade,...
EYFLA4A User Guide - Page 11
... the tool is not operated for the work being tightened: Material, seating surface finish
Setting the tool to configuration mode
1. Press the and buttons to configuration mode. Configuring the torque clutch setting (1)
(2)
NOTE: • Tools ship from the factory set to "F" mode (torque control function off). • The control panel will turn off...
EYFLA4A User Guide - Page 12
... lamp
2.
Model
EZFLA4 EZFLA5
Number of torque stages and the snug point detection level. • The tool's panel will be sure to check the new setting value. (See page 14.)
IMPORTANT INFORMATION: • You can select from 30 torque clutch settings (1 to 30). • Use figures from the Tightening Torque Chart to guide your...
EYFLA4A User Guide - Page 13
...EYFLA5(M6)
EYFLA4(M6)
EYFLA4(M8)
0
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
Measurement conditions • Temperature: Room temperature (20°C/68°F)
Using the Interval Set • The interval set operates to set... buttons to prevent the tool
from operating after changing the setting.
- 13 - High
• Tightening bolts in materials...
EYFLA4A User Guide - Page 14
....
• Control panel display Display: The torque set lights up. Press the interval set button.
• Control panel display Display: The interval set lights up . Set the tool to register the tool and assembly qualifier, see the assembly qualifier instruction manual. Press the and buttons to accept the selected setting. • The control panel will be turned...
EYFLA4A User Guide - Page 15
... parts (hammer, etc.) used in the following chart before resuming use .
The tool is being displayed, the control panel will display an error message...serviced. Display
Tool circuit
H6
EYFLA4
H7
EYFLA5
H8
EYFLA6
H9
EYFMA1
NOTE: • If you engage the switch while a setting is too hot to the torque clutch setting display. Error Display
In the event of the tool.
Replace...
EYFLA4A User Guide - Page 16
...176;C (41°F) to prevent dust or dirt from the main body of the tool, replace the battery pack cover immediately in a location where the temperature is 5°C (41°...battery that the terminals on how to recycle this battery.
[Battery Charger]
Charging
Read the operating manual for Panasonic battery charger for an hour in order to 40°C (104°F).
MAINTENANCE
Use only a ...
EYFLA4A User Guide - Page 17
..., install and use in a particular installation. Use only the battery pack specified in a residential installation. FCC ID: O4O-EYFLA IC : 8507A-EYFLA
The enclosed device complies with provided instructions. Panasonic Electric...accept any interference received, including interference that may cause harmful interference to part 15 of the following two conditions: (i.) this device may not cause ...
EYFLA4A User Guide - Page 18
... with battery 1.3 kg (2.8 lbs) 1.3 kg 1.35 kg 1.3 kg 1.35 kg
pack: EYFB30)
(2.8 lbs) (2.9 lbs) (2.8 lbs) (2.9 lbs)
---------
Full: 65 min. SPECIFICATIONS
MAIN UNIT
Model
Motor Chuck size
EYFLA4
A
AR
Single- 9 - 9.5 mm ended (23/64" - 3/8")
EYFLA5
A AR Q QR
10.8 V DC
9 - 9.5 mm □9.5 mm
(23/64"
(3/8")
- 3/8")
EYFLA6
EYFMA1
P,J PR,JR
P,J
14.4 V DC
□12.7 mm...
EYFLA4A User Guide - Page 19
...(13/32") Approximately 29 g (0.6 lbs)
Assembly Qualifier (not included with shipment)
Model Rating Dimensions
Weight
EYFRZ01
EYFR02
See the rating plate on the bottom of the Assembly Qualifier...
Model Indoor/Urban Range Outdoor RF line-of-sight range Transmit Power Assembly Qualifier Sensitivity FCC Part 15.249 Industry Canada
EYFLA 100ft./30m 300ft./100m 1mW(0dBm) -92dBm(1% packet error)...
EYFLA4A User Guide - Page 56
PANASONIC CONSUMER ELECTRONICS COMPANY
One Panasonic Way, Secaucus, New Jersey 07094
EN, FR, ES EY9810FLA43 2011 08
Printed in Japan
Panasonic EYFLA5P Reviews
We have not received any reviews for Panasonic yet.