AKHRP200 User Guide
Page 2
... card 9 5 Save ROP configuration file to transfer, copy, disassemble, decompile, and reverse engineer the software included with the unit, as well as "memory cards". Contents Introduction 3 Setup mode 4 Setup mode 4 Setup Mode Operations 7 1. Set buzzer (beep/call tone 11 9 Display brightness setting (LED/7-segment display ...12 18 Save unit data to memory card 12 19 Software upgrade 12 Error messages in which each of them is discussed separately. • Personal computers are referred to individually in descriptions in setup mode 13 ROP menu operations 14 ROP menus that can...
... card 9 5 Save ROP configuration file to transfer, copy, disassemble, decompile, and reverse engineer the software included with the unit, as well as "memory cards". Contents Introduction 3 Setup mode 4 Setup mode 4 Setup Mode Operations 7 1. Set buzzer (beep/call tone 11 9 Display brightness setting (LED/7-segment display ...12 18 Save unit data to memory card 12 19 Software upgrade 12 Error messages in which each of them is discussed separately. • Personal computers are referred to individually in descriptions in setup mode 13 ROP menu operations 14 ROP menus that can...
AKHRP200 User Guide
Page 4
...a scene file stored on a memory card. Sets the brightness of unit settings, and save and load scene files and user files. Upgrades the software used by the unit. 4 Formats a memory card Selects the flare and pedestal control function Enables or disables the buzzer or call tone) 9 ...the panel LED and 7-segment display. It also allows you to do any of the software used by the unit. Initializes unit settings. Normal operation is not available either. Setup mode functions Setup mode allows you to load a configuration file for the unit to memory card 19 Upgrade...
...a scene file stored on a memory card. Sets the brightness of unit settings, and save and load scene files and user files. Upgrades the software used by the unit. 4 Formats a memory card Selects the flare and pedestal control function Enables or disables the buzzer or call tone) 9 ...the panel LED and 7-segment display. It also allows you to do any of the software used by the unit. Initializes unit settings. Normal operation is not available either. Setup mode functions Setup mode allows you to load a configuration file for the unit to memory card 19 Upgrade...
AKHRP200 User Guide
Page 6
...UP+DOWN SAVE/LOAD EXIT EXECUTE CAMERA 10-19 No. Press to select a menu number. segment display) - - - - - - Setup mode (continued) Setup mode menu configuration Setup mode is comprised of the menus and submenus listed in the table below. ND LED CC 7-segment display 10 11 12 For...(1 to 4) Scene files (1 to 4) User files (1 to 3) User files (1 to 3) Lens files (1 to 32) Lens files (1 to memory card - - 19 Upgrade software - - Use or to /load ROP configuration file from memory card 6 Format memory card*1 7 Select/set value or an operation. No.
...UP+DOWN SAVE/LOAD EXIT EXECUTE CAMERA 10-19 No. Press to select a menu number. segment display) - - - - - - Setup mode (continued) Setup mode menu configuration Setup mode is comprised of the menus and submenus listed in the table below. ND LED CC 7-segment display 10 11 12 For...(1 to 4) Scene files (1 to 4) User files (1 to 3) User files (1 to 3) Lens files (1 to 32) Lens files (1 to memory card - - 19 Upgrade software - - Use or to /load ROP configuration file from memory card 6 Format memory card*1 7 Select/set value or an operation. No.
AKHRP200 User Guide
Page 12
... [18]. Press to flash after the restart. If this happens, check the memory card and try again or insert another memory card to "Software upgrades"(→page 3). 1. Press or to select [y] and press to confirm the selection. • After confirmation, unit settings are attempting to...SYNC M.PED IRIS DOWN SET UP DISPLAY SELECT ND/CC M.GAIN/M.PED SHUTTER SHIFT + UP+DOWN SAVE/LOAD EXIT EXECUTE CAMERA 10-19 No. Setup Mode Operations (continued) 2. Press to confirm the selection. • Upgrading starts. Press or to select [y] and press to select the menu ...
... [18]. Press to flash after the restart. If this happens, check the memory card and try again or insert another memory card to "Software upgrades"(→page 3). 1. Press or to select [y] and press to confirm the selection. • After confirmation, unit settings are attempting to...SYNC M.PED IRIS DOWN SET UP DISPLAY SELECT ND/CC M.GAIN/M.PED SHUTTER SHIFT + UP+DOWN SAVE/LOAD EXIT EXECUTE CAMERA 10-19 No. Setup Mode Operations (continued) 2. Press to confirm the selection. • Upgrading starts. Press or to select [y] and press to select the menu ...