Oreck Air 6 Support and Manuals
Get Help and Manuals for this Oreck item
Popular Oreck Air 6 Manual Pages
Owners Guide - Page 1
Table Top Air Cleaner Super Air 5 / Air 6
Model 447628 & 4478801 S I M P LY
A M A Z I N G®
Service Manual
REV I., Please disregard all earlier versions.
Owners Guide - Page 2
... IGNITION AND SUBSEQUENT PERSONAL INJURY OR PROPERTY DAMAGE. 9. General Knowledge Warning - Read all instructions. 2. Important Safeguards
When using electrical appliances consideration should be given to service the equipment without the above the fan. WARNING: DO NOT USE THIS ELECTRONIC AIR CLEANER WHEN OXYGEN IS
BEING USED OR WHEN COMBUSTIBLE GASES ARE PRESENT. Attempting to basic...
Owners Guide - Page 3
... combines antimicrobial treatment and activated charcoal. Some of air pollution. The fan pulls in the dirty air receive a positive electrical charge as they pass through the unit by the washing process. Table of Contents
General Description and Operation page 3 Periodic Maintenance and Tune-Up page 4 Trouble Shooting Guide page 5 Parts Removal and Replacement Procedures page 15 Cross...
Owners Guide - Page 5
... interlock switch with a plastic handle screwdriver to determine if it for much of the servicing portion of troubleshooting. d. If the top appears to test operation. Activator Post
Interlock Switch
Turn the top over and examine it for proper positioning. Initially:
1. Problem Being Checked:
1. If the motor and blower do not operate: a.
Check the top...
Owners Guide - Page 7
...switch is bad.
7. Check to see if the "cleaning air" light comes on line side of the switch but the green "cleaning air" light does not operate: a. If there is voltage at...top from the switch when activated. If carbon tracking is apparent, clear and retest the cell. Troubleshooting Guide
6.
Check to and from engaging the interlock switch. If the problem persists, replace the cell.
Owners Guide - Page 8
.... If the voltage is not present, check the transformer output. Troubleshooting Guide
c. You should measure from the light terminals on the power supply... about 16 volts DC. probe and a multimeter.
The unit must be replaced.
Option 1: Check the output of the power supply by using the recommended... Set meter to observe a spark.
8 If the wire has voltage, the light is ...
Owners Guide - Page 10
... and grime from the motor shaft using a soft cloth. If there are no signs of dirt and grime on the shaft to the blower wheel. Troubleshooting Guide
d. If the blower wheel vibrates: a. Replace the blower wheel if blades appear warped or bent.
Owners Guide - Page 11
...Check for damage or excessive wear. A distorted motor bracket normally indicates motor overheating.
Replace parts as needed. d. You may cause the wheel shaft to disengage the snaps. Inspect ...the tabs out of the outboard bearing. replace it may drag on both sides. e. Troubleshooting Guide
c. The blower wheel should be firmly supported, allowing no movement other than rotation. ...
Owners Guide - Page 15
Super Air 5 Model 447628
Parts Removal and Replacement
General Parts Replacement
Motor Removal and Replacement page 16 Power Supply Removal and Replacement page 19
Transformer Removal and Replacement page 21 Bearing Wall Assembly and
Blower Wheel Removal and Replacement page 22 Led Assembly Removal and Replacement page 23 Cell Assembly Removal and Replacement page 23 Ionizer Needle Removal and ...
Owners Guide - Page 17
... the center support rib and ... servicing the unit and repairing...air and keep objects and internal electrical wiring away from the cabinet while releasing the tabs. Unit has a rotating blower wheel and cooling fan to release the motor mounting bracket locking tabs by gently grasping the outside of the slot. After releasing all four tabs, remove the bracket.
17 General Parts Replacement...
Owners Guide - Page 20
... the cabinet at an angle while rotating it is routed properly and cannot contact motor fan and is supplied with the equipment you keep the unit cool. Failure to a 24V signal that hold the board in the service manual for rotating members can cause electrical shock, personal injury or property damage. This equipment...
Owners Guide - Page 21
... a rotating blower wheel and cooling fan to selector switch position 4 using...away from the rotating elements. General Parts Replacement
5. Reverse step 1. Save for ...proper clearance for installment of Motor
Removal and Replacement. Use standard precautions... new transformer. Transformer Removal and Replacement 1. When servicing the unit and repairing the unit always insure that secure...
Owners Guide - Page 24
... allow about 1/4" distance between the motor end bracket and the fan hub. When servicing the unit and repairing the unit always insure that is clear of Motor Removal and Replacement.
Fan Blade Removal and Replacement 1. Follow steps 1, 2, 3, and 6 of all other end. Failure to circulate air and keep objects and internal electrical wiring away from all objects...
Owners Guide - Page 25
...21
1
1
2
NLA
3
1
1
PART NO. 242235-001 242331-007 242404-001 ...FAN) CABINET TOP, GRAY COLLECTOR CELL ION NEEDLE ASSEMBLY STRIPPER MOTOR MOUNTING BRACKET DRIVE GROMMET HV POWER SUPPLY BOARD HV POWER SUPPLY BOARD "HUMP BACK" CABINET BOTTOM MOTOR ISOLATOR PAD SWITCH ASSEMBLY SWITCH ROCKER CARTON CARTON INSERT CHARCOAL FILTERS (NO LONGER AVAILABLE) CHARCOAL FILTERS CELL CLEANER OWNER'S MANUAL...
Owners Guide - Page 28
All trademarks are owned and used under the authority of Oreck Holdings, LLC. 75422-01 REV I 08/04 R-7693, R-7695 All rights reserved. ©2004 Oreck Holdings, LLC.
Oreck Air 6 Reviews
We have not received any reviews for Oreck yet.