Optoma W415 Support and Manuals
Get Help and Manuals for this Optoma item
Popular Optoma W415 Manual Pages
User Manual - Page 2
Table of contents
Options...43 Options | Input Source 46 Options | Remote Settings 47 Options | Advanced 48 Options | Lamp Setting 50 LAN_RJ45...52
Appendices 62 Troubleshooting 62
Image...62 Other...63 Projector LED Status Indicator 64 Remote Control...65 Replacing the Lamp 66 Compatibility Modes 69 Video Compatibility 69 Video Timing Detail Describe 69 Computer Compatibility - VESA ...
User Manual - Page 4
... of its life, the
projector will detect the life of its life time, the message "Replacement suggested" will show on -screen display "System|Lamp Setting" menu after replacing the lamp module (refer to rain or moisture. To replace the lamp, follow all warnings, precautions and maintenance as possible.
4 Please do not expose this user's guide.
▀■ Warning-
▀...
User Manual - Page 7
...
Documentation :
User's Manual Warranty Card Quick Start Guide WEEE Card
7
Projector with lens cap
Power Cord 1.8m 15 pin D-sub VGA Cable
Noottee
Due to ensure all parts listed below are in each Country, some regions may have different accessories.
If something is missing, please contact Optoma customer service. English
Introduction
Package...
User Manual - Page 13
... to switch the
display output to the projector. (Check the user manual of the
laptop to determine the appropriate ...Settings on the projector
button to the projector. The projector's startup logo screen displays and connected
devices are detected. Noottee
3.
English
Installation
Powering On/Off the Projector
Powering On the Projector
1. Connect the power cord to turn On the projector...
User Manual - Page 14
...
▀■ When the Lamp LED indicator lights red, the projector will disappear in 5 seconds. 2. Contact the nearest service center if the projector displays these symptoms. See page...problem persists, you must wait until the projector has completed the cooling cycle and has entered standby mode. If you wish to turn the projector back on , 2 sec off the projector. The projector...
User Manual - Page 21
...is only supported in for...IMAGE | Advanced DISPLAY
DISPLAY | 3D SETUP
SETUP | Security SETUP | Audio Settings
SETUP | Advanced SETUP | Network
Display Mode Brightness Contrast Sharpness ...Projector ID Audio Settings
Advanced Network
Security Setting Security Timer Change Password
Exit Internal Speaker
Mute Volume Audio Input
Exit
Logo Logo Capture Closed Captioning
Exit
LAN Settings Control Settings...
User Manual - Page 26
Set projector signal properties. Signal
Enter the Signal menu. See page 28 for more information.
26
The function is available when input source is support VGA 1/VGA 2. User Controls
Color Matching
Enter the Color Matching menu. See page 27 for more details.
User Manual - Page 32
... menu location on the display screen. User Controls
Setup
Language
Enter the Language menu.
Screen Type
Press ◄► to set the aspect ratio to 16:9 or 16:10.
You can project from behind a translucent screen.
Front Ceiling
When you select this function, the projector turns the image upside down for ceiling-mounted...
User Manual - Page 35
English
User Controls
Setup | Security
Noottee
The default password: 1, 2, 3, 4, 5. When security is enabled, the following screen displays at startup and before access to power on the projector
and access the Security menu.
Off-no password is allowed:
35
Security Setting
Enable or disable the security password.
On-the current password is required to the Security menu is required...
User Manual - Page 39
is saved as the startup screen. 1. Display the desired screen on the projector. 2.
Select OK. When finished, Screen capture Succeeded will display. Closed Captioning
Select the screen to display during startup.
Optoma-the supplied default startup screen. Neutral- Select Logo Capture from the Advanced menu. The captured screen is Background Color. User-customized...
User Manual - Page 41
... IP address manually.
IP Address-Select an IP address Subnet Mask-Select subnet mask number. Gateway-Select the default gateway of the network connected
to the projector.
DNS-Select DNS number. Apply-Press "ENTER" to the projector from the DHCP server automatically. If the connection is connected. English
User Controls
Setup | LAN Settings
Noottee
Network...
User Manual - Page 52
... and Contrast settings.
The LAN/RJ45 function of the projector through a network, such as : VideoSource, Sound-Mute, etc. Wired LAN Terminal functionalites
The projector can be controlled...trademark of AMX LLC of operation, the Optoma projector provides diverse networking and remote management features. http://www.crestron.com/ This projector is supported by JBMIA. http://www.amx.com/
...
User Manual - Page 62
... "Replacing the Lamp" section.
Make sure you have removed the lens cap and the projector is between the required distance
from the projector. Please
refer to the following:
Please setup the display format as - T he image is still stretched, you will
show the best image in 16: 9 format on .
Appendices
Troubleshooting
If you experience a problem...
User Manual - Page 77
...Lamp fail/Fan Lock/Over Temperature/
Lamp Hours Running Out/Cover Open
INFOn
n : 0/1/2/3/4/6/7/8/ =
Standby/Warming/Cooling/Out of Range
/Lamp fail/Fan Lock/Over Tmperature/
Lamp Hours Running Out/Cover Open
READ from projector
232 ASCII Code HEX Code
Function
Projector...on Screen Type setting
~XX128 1
7E...Model name
OKn
n:1/2=W415/EH415
~XX108 1
7E 30 30 31 30 38 20 31 0D Lamp...
User Manual - Page 80
... JBMIA PJLink™ Class 1. LAMP?
This projector is returned. available inputs
"11 12 21 22 31 32"
Inquiry about the The projector name set on
Inquiry about the manufacturer name
"Optoma" is fully compliant to the specifications of JBMIA PJLink™ Class 1.
AVMT AVMT? NAME? Appendices
Noottee
This projector is returned.
80 It supports all the commands defined...
Optoma W415 Reviews
We have not received any reviews for Optoma yet.