Netgear XCM8948 Support and Manuals
Get Help and Manuals for this Netgear item
This item is in your list!
View All Support Options Below
Free Netgear XCM8948 manuals!
Problems with Netgear XCM8948?
Ask a Question
Free Netgear XCM8948 manuals!
Problems with Netgear XCM8948?
Ask a Question
Popular Netgear XCM8948 Manual Pages
Command Line Interface CLI User Manual Software Version 11.x - Page 2
.... You must register your Internet service provider for technical support.
For product updates and web support, visit http://support.netgear.com. Phone (US & Canada only): 1-888-NETGEAR. M5300, M6100, and M7100 Series ProSAFE Managed Switches
Support
Thank you can use it to register your product through the NETGEAR website.
After installing your device, locate the serial number...
Command Line Interface CLI User Manual Software Version 11.x - Page 4
...Filtering Commands 175 Dual Image Commands 177 System Information and Statistics Commands 178 Switch Services Commands 207 Logging Commands 209 Email Alerting and Mail Server Commands 217 System ... Commands 245 DNS Client Commands 258 IP Address Conflict Commands 263 Serviceability Packet Tracing Commands 264 Support Mode Commands 302 Cable Test Command 305 Power Management Commands 306...
Command Line Interface CLI User Manual Software Version 11.x - Page 54
... M5300-28G3 ProSafe 24-port Gigabit L3 with 10 Gigabit Stacking Detected Code in the database of the switch type.
Management Preference
The management preference value of supported switch types.
Model Identifier The model identifier for the supported switch type. Model Identifier The model identifier for the supported switch type. Switch Description The description for the...
Command Line Interface CLI User Manual Software Version 11.x - Page 91
... address prefix.
Use this command in Management access-list configuration mode. Each rule requires a unique priority.
M5300, M6100, and M7100 Series ProSAFE Managed Switches
permit service
This command sets permit conditions for the management access list based on the source IP address of a packet.
Command Line Interface CLI User Manual Software Version 11.x - Page 92
... priority.
M5300, M6100, and M7100 Series ProSAFE Managed Switches
deny service
This command sets deny conditions for the rule. Format Mode
deny priority priority Management ... Mode
deny service service [priority priority] Management access-list configuration
Parameter service priority
Definition Indicates the service type: telnet, ssh, http, https, or snmp. You cannot update or remove...
Command Line Interface CLI User Manual Software Version 11.x - Page 372
... default CIST ID) as a number in the range of only the root bridge sending BPDUs, and supports the discarding, learning, and forwarding states. Default Format Mode
Disabled spanning-tree mode {mst | pvst ... in PVRSTP. If you specify the cost option, the command sets the path cost for this port within a specific multiple spanning tree instance or the common and internal spanning tree ...
Command Line Interface CLI User Manual Software Version 11.x - Page 656
M5300, M6100, and M7100 Series ProSAFE Managed Switches
Command example: The following example sets priority 3 to carry the dot1p value through the network.
Format Mode
no -drop
Data Center Commands 656 Additionally, the dot1pmapping to class of service must configure the same no-drop priorities across the network in order to no drop...
Command Line Interface CLI User Manual Software Version 11.x - Page 838
...• Routing Policy Commands
The commands in the NETGEAR Managed Switch software BGP package. Reset part of the switch. 12. Display switch settings, statistics, and other information. • Configuration ... (BGP), which is an exterior gateway routing protocol that displays the configuration setting. • Clear commands.
Border Gateway Protocol Commands
12
This section describes ...
Software Administration Manual Software Version 11.x - Page 14
... Stack Members 496 Stack Member Numbers 496 Stack Member Priority Values 496 Install and Power-up a Stack 496 Compatible Switch Models 496 Install a Switch Stack 497 Switch Firmware and Firmware Mismatch 498 Upgrade the Firmware 498 Migrate Configuration with a Firmware Upgrade 499 Web Interface: Copy Master Firmware to a Stack Member 499 Stack Switches Using Ethernet Ports and a Stack...
Software Administration Manual Software Version 11.x - Page 302
... the most valuable uses of service: how to support Voice over IP (VoIP). Set queue 5 on all VoIP packets.
The configuration script is to set up a class for Router ...Configure DiffServ for the switch.
(Netgear Switch) #config (Netgear Switch) (Config)#cos-queue strict 5 (Netgear Switch) (Config)#diffserv
DiffServ
302
Software Administration Manual Activate DiffServ for VoIP
1. This ...
Software Administration Manual Software Version 11.x - Page 487
... chassis switch. NETGEAR recommends that the new firmware starts running the correct firmware. Then issue the copy command to make sure that were not updated.
4. After code is occurring.
2.
If an error occurs during code propagation, do not come up, and the show chassis command shows a code mismatch error.
1. Chassis Switch Management
487
Software Administration Manual Then reset...
Software Administration Manual Software Version 11.x - Page 499
...
default settings). 5.
This saved configuration is up, download the saved configuration to the master switch and other switches in stack configuration mode. 3. Click Apply. Select Maintenance > File Management > Copy. Switch Stacks
499
Software Administration Manual Managed Switches
a. After the firmware is not carried forward in a firmware update, to download new firmware to...
User Manual Software Version 11.x - Page 16
.../M7100/M5300 Switch Module Installation Guide. • M6100/M7100/M5300 Software Setup Manual. • M6100/M7100/M5300 User Manual (this document). Registration confirms that your email alerts work, lowers technical support resolution time, and ensures that your shipping address accuracy. Understanding the User Interfaces
The managed switch software includes a set of comprehensive management...
Product Data Sheet - Page 37
...Operational Neighbor Discovery Problems
Data Center
IEEE 802.1Qaz Draft 2.4 - ETS (Enhanced Transmission Selection)
DCB Capability Exchange Protocol Base Specification Rev 1.06 -...Model for IEEE 802.1Q devices
RFC 2737 - SNMP Community MIB
RFC 3584 - POWER-ETHERNET-MIB
RFC 2579 - SNMPv2 Management Information Base
ANSI/TIA 1057 - Integrated Services MIB
FASTPATH Enterprise MIBs supporting...
Web Management User Guide - Page 392
... Web Management User Guide
5. Click Cancel to cancel the configuration on the screen and reset the data on the screen to the latest value of this service interface, either Up...settings on which one can be selected. Shows the operational status of this service interface is not supported by the platform.
Use Interface to select the interface on the page, click Apply to send the updated...
Netgear XCM8948 Reviews
Do you have an experience with the Netgear XCM8948 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Netgear yet.
Earn 750 points for your review!