Netgear GSM712 Support and Manuals
Get Help and Manuals for this Netgear item
View All Support Options Below
Free Netgear GSM712 manuals!
Problems with Netgear GSM712?
Ask a Question
Free Netgear GSM712 manuals!
Problems with Netgear GSM712?
Ask a Question
Popular Netgear GSM712 Manual Pages
Configuring MAC ACLs - Page 1
... the VoIP phones. Specifically, our example will demonstrate how to restrict access to ports on a switch based on the switch). the source MAC address of VoIP telephones and a single management PC. Other devices will use MAC ACLs to restrict access to a set up MAC ACLs. This example uses a Netgear ProSafe FSM7328PS layer 3 managed switch.
1. Configuration
•...
Configuring MAC ACLs - Page 2
...8226; Go to MAC Rules • Enter the first rule with an ID of 1 • Set the Action to Permit • Under Source MAC enter the MAC address
of one of the '...the management PC is ID 16)
• Next, we will add the ACL we created to the required ports on the switch
• Go to MAC Binding Configuration • Choose the ACL 'AllowVoIPTelephones'
from the ACL ID list
• Click on ...
Configuring Link Aggregation (LAG) between two NETGEAR managed switches - Page 1
...switches:
• FSM7328PS (Switch 1) • FSM7328S (Switch 2)
We will configure a LAG between two NETGEAR managed switches. LAG allows a switch to treat multiple physical links between two end-points and adds redundancy. ports 25 and 26 on each switch... the Link Aggregation sense is being used). This is sometimes referred to Configure LAG
Version 1.1
How to as a single logical...
Configuring Link Aggregation (LAG) between two NETGEAR managed switches - Page 2
... in the LAG (maximum of the below configuration is done under Switching -> LAG.
1.1
• Under LAG Configuration, add a LAG as shown above. • Set Link Trap, STP Mode and Static Mode to Enable or Disable as required. • If Link Trap is set to Disable means
LACP is enabled on Unit 1 • Check...
Configuring Link Aggregation (LAG) between two NETGEAR managed switches - Page 3
1.3
• Click back to LAG Configuration to Configure LAG
Version 1.1 Create the LAG on Switch 2
All of the below configuration is done under Switching -> LAG.
2.1
• Under LAG Configuration, add a LAG as shown above.
2.2
• Under LAG Membership, add the ports ... 25 and 26 • Press Apply
How to see a summary of eight).
• Expand the ports in the switch by clicking on...
Configuring Link Aggregation (LAG) between two NETGEAR managed switches - Page 4
Connect the LAG links between the LAGs on each switch are connected, LAG State will be defined as Link Up under LAG Configuration.
3.2
• LAG ...and then the LAG itself added to ports 25 and 26 on switch 2.
3.1
• Once the links between the switches
Connect ports 25 and 26 on switch 1 to the VLAN(s) as Link Up on Switch 2.
4.
How to Maintenance -> Save Config.
3. Note with ...
GSM712 Product datasheet - Page 1
...e Simple to setup and use it ! C o s t E f f e c t i v e Moderately priced to boost your network throughput without blowing your workplace.
And you want .
saving the management features until you can use , with an intuitive browser interface for maximized productivity in your budget.
®
May 27, 2003 Netgear GSM712
Netgear, Inc. GSM712
12-port Managed Gigabit Switch
•...
GSM712 Product datasheet - Page 2
... kit - FSM726S 24+2 Managed Stackable Switch - NETGEAR®, the Netgear logo, The Gear Guy, Everybody's connecting and Auto Uplink are trademarks or registered trademarks of Service (CoS) - Used under license.
** Free basic installation support provided for GBIC modules -
D-GSM712-1
U
®
L
GSM712
Technical Specifications • Network Protocol and Standards Compatibility...
Netgear GSM712 Reviews
We have not received any reviews for Netgear yet.