Milwaukee Tool 2996-22 Support and Manuals
Get Help and Manuals for this Milwaukee Tool item
View All Support Options Below
Free Milwaukee Tool 2996-22 manuals!
Problems with Milwaukee Tool 2996-22?
Ask a Question
Free Milwaukee Tool 2996-22 manuals!
Problems with Milwaukee Tool 2996-22?
Ask a Question
Popular Milwaukee Tool 2996-22 Manual Pages
Service Parts List 2 - Page 1
... label will fit on all catalog numbers listed above except 48-11-1850R: Order Fig. 4. REVISED BULLETIN
DATE
Sept. 2022
WIRING INSTRUCTION
2, 3
1, 4 NOTE: For 48-11-1850R: Order Fig. 3 & 4. The area intended for any adhesive label or nameplate must be applied with equipment). MILWAUKEE TOOL l www.milwaukeetool.com 13135 W. SERVICE PARTS LIST
BULLETIN NO.
54-04-1820
SPECIFY...
Operators Manual - Page 2
.... •Do not overreach. Slippery handles and grasping surfaces do the job better and safer at all instructions listed below may result in the warnings refers to become complacent and ignore tool safety principles. The term "power tool" in serious personal injury. •Use personal protective equipment. Unmodified plugs and matching outlets will do...
Operators Manual - Page 3
...the auxiliary handle(s). contact Milwaukee Tool or
a trained professional for Canada and U.S.
3 SPECIFICATIONS
Volts 18 DC Battery Type M18™ Charger Type M18™ Recommended Ambient
...service damaged battery packs. SPECIFIC SAFETY RULES FOR DRILL/DRIVER
Safety instructions for a free
replacement.
•
WARNING
Some dust created by the manufacturer or authorized service ...
Operators Manual - Page 4
... the specified for the job. cific charging instructions, read the operator's
manual supplied with a spindle lock. To insert the battery, slide the pack into place. Make sure it latches securely into the body of the tool. Ensure side
handle is tightened securely before inserting or removing bits. Installing the Side Handle
1. Only use .
This...
Operators Manual - Page 5
...to cycle between the settings. This will blink green. Clutch Setting
1-4 5-8 9-11 12-14
TORQUE SPECIFICATIONS
in hardwood. lbs
Applications...the light will be solid green. The torque specifications shown here are only a guide, use water to a complete stop before use... in line with the arrow. If the tool detects a sudden twisting motion, the tool will shut off and the light will damage...
Operators Manual - Page 6
... tool down.
Screws can cause severe in as
little as undue noise, misalignment or binding of moving parts, breakage of it away from vents.
To replace the... a
MILWAUKEE service facility for repairs.
Always use flammable or combustible solvents around tools. Hard materials like concrete require more pressure.
Repairs For repairs, return the tool, battery...
Operators Manual - Page 7
... Mexico, Mexico
Model: Date of MILWAUKEE's website www.milwaukeetool.com or call 1.800. CANADA Milwaukee Tool (Canada) Ltd
1.800.268.4015
Monday-Friday, 7:00 AM - 4:30 PM CST or visit www.milwaukeetool.ca
LIMITED WARRANTY USA & CANADA
Every MILWAUKEE power tool* (see exceptions below) is three (3) years from the end-user
guide or instruction manual. Subject to be replaced free of...
Service Parts List - Page 1
....3878)
Or Return it to this location for service. J79A & J79B
REVISED BULLETIN
DATE
Aug 2021
WIRING INSTRUCTION
Service for Milwaukee Tool ONE KEY Products can only be included with the return product.
A copy of the proof of purchase should be performed at this
Milwaukee factory Central Repair Center:
MILWAUKEE TOOL Central Repair 1401 Sycamore Avenue l Greenwood, MS 38930-7277
Please...
Service Parts List - Page 2
...PART
NO. Place a T40 1/4" torx bit into the chuck opening, directly to the head of reversing screw just prior to use a 12"-18" metal tube or pipe as leverage over the boxed wrench. In a clockwise direction apply a slow, steady force on the 'cheater bar' to the #1 setting...22
21 22 23
26
52
25 26
25
FIG. INSTALLING... the tool into the... Carrying Case
(1)
Service Namelate
(1)
Warning ...
Operators Manual 1 - Page 2
... situation. A and free from heat, oil, sharp edges or moving parts, breakage of tools allow you are connected and properly used. and control of flammable liquids, gases or dust. A wrench or a key left attached to rain or wet conditions. Save all instructions listed below may ignite the dust or fumes. •Keep children and...
Operators Manual 1 - Page 3
... of the power tool "live " wire may make exposed metal parts of injury. •Do not expose a battery pack or tool to
cause cancer, birth defects or other
construction activities contains chemicals known to fire or excessive temperature. SPECIFIC SAFETY RULES FOR IMPACT DRIVER
•Hold the power tool by a qualified repair person using tools. Fasteners contacting a "live...
Operators Manual 1 - Page 4
... and driver bits. 1. Forward
CENTER TO LOCK
Reverse
1. cific charging instructions, read the operator's
manual supplied with ANSI Z87.1. Only use .
2. The trigger will blink blue. NOTE: An LED is turned on the trigger. Release the ring. Always remove battery pack before storing the tool and any speed from 0 to the maximum speed set to...
Operators Manual 1 - Page 5
... the risk jury and damage,
of personal innever immerse
tighter it will repair or replace any part on an electric power tool which, after examination, is determined by MILWAUKEE to be defective in material or workmanship for a period of five (5) years** after the date of purchase unless otherwise noted.
Hoist - allow a liquid to www.milwaukeetool.com...
Operators Manual 1 - Page 6
...-user
guide or instruction manual. The warranty period for the Work Light is for the M18™ Compact Heat Gun, 8 Gallon Dust Extractor, M18™ Framing Nailers, M18 FUEL™ 1/2" Ext. If during normal use the LED or LED Bulb fails, the part will be replaced free of use are not normal. ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT REMEDIES...
Service Parts List 1 - Page 1
... Central Repair 1401 Sycamore Avenue l Greenwood, MS 38930-7277
Please send your tool directly to a MILWAUKEE factory Service Center location, freight prepaid and insured. WHEN ORDERING PARTS
M18™ FUEL™ ONE KEY 1/4" Hex Impact Driver
CATALOG NO. 2857-20
STARTING SERIAL NO. Drwg. 2
J64A
BULLETIN NO. 54-00-2857
REVISED BULLETIN
DATE
May 2019
WIRING INSTRUCTION
Service...
Milwaukee Tool 2996-22 Reviews
We have not received any reviews for Milwaukee Tool yet.