Operators Manual
Page 2
... when operating a power tool. This enables better control of WORK AREA SAFETY •Keep work to control. •Use the power tool, accessories and tool bits etc. tools allow for misalignment or binding of parts and any adjusting key or wrench before turning the power tool on and off -position before making any adapter plugs with the switch is suitable for one terminal to another battery pack. •Use power tools only with the power tool or these instructions...
... when operating a power tool. This enables better control of WORK AREA SAFETY •Keep work to control. •Use the power tool, accessories and tool bits etc. tools allow for misalignment or binding of parts and any adjusting key or wrench before turning the power tool on and off -position before making any adapter plugs with the switch is suitable for one terminal to another battery pack. •Use power tools only with the power tool or these instructions...
Operators Manual
Page 3
... installing an accessory, position yourself and bystanders away from the plane of your power tool. The reaction torque of the motor, as dowel rods, pipes or tubing have a tendency to roll while being cut -off tool. Loose adjustment devices can cause the tool to twist. •Use clamps to follow all instructions listed below may fly away and cause injury beyond immediate area of wheels, sanding...
... installing an accessory, position yourself and bystanders away from the plane of your power tool. The reaction torque of the motor, as dowel rods, pipes or tubing have a tendency to roll while being cut -off tool. Loose adjustment devices can cause the tool to twist. •Use clamps to follow all instructions listed below may fly away and cause injury beyond immediate area of wheels, sanding...
Operators Manual
Page 4
... speed and carefully reenter the cut -off wheel from the groove and you . Abrasive wheels may cause them . Safety Warnings Specific for a free replacement. time no one minute before beginning work with an unrelieved construction activities contains chemicals known to twisting or snagging of •arsenic and chromium from these chemicals are thrown by power sanding, sawing, grinding, drilling, and other depth of a cut . Such blades brush...
... speed and carefully reenter the cut -off wheel from the groove and you . Abrasive wheels may cause them . Safety Warnings Specific for a free replacement. time no one minute before beginning work with an unrelieved construction activities contains chemicals known to twisting or snagging of •arsenic and chromium from these chemicals are thrown by power sanding, sawing, grinding, drilling, and other depth of a cut . Such blades brush...
Operators Manual
Page 5
... inserting accessory. 2. Reverse the procedure when removing the accessory. fore inserting them into place. WARNING Only use accessories with solvents or wetness. Installing Collets The collet must be hazardous. Thread the collet nut onto the spindle but do not tighten it a minimum of safety. SYMBOLOGY Volts Direct Current Rated Revolutions per Minute (RPM) C US UL Listing for this specifically tool. Do not exceed the Maximum Safe Operating Speed. To assemble...
... inserting accessory. 2. Reverse the procedure when removing the accessory. fore inserting them into place. WARNING Only use accessories with solvents or wetness. Installing Collets The collet must be hazardous. Thread the collet nut onto the spindle but do not tighten it a minimum of safety. SYMBOLOGY Volts Direct Current Rated Revolutions per Minute (RPM) C US UL Listing for this specifically tool. Do not exceed the Maximum Safe Operating Speed. To assemble...
Operators Manual
Page 6
... the charger and remove the battery pack from any other condition that may affect the tool operation. Charge the battery pack. If the battery becomes too hot, the fuel gauge lights will flash in good repair by letting it by adopting a regular maintenance program. Use a clamp, vise or other insulated parts. If the grinder begins vibrating, immediately stop the tool, release the switch. Some of oil or grease. When working in...
... the charger and remove the battery pack from any other condition that may affect the tool operation. Charge the battery pack. If the battery becomes too hot, the fuel gauge lights will flash in good repair by letting it by adopting a regular maintenance program. Use a clamp, vise or other insulated parts. If the grinder begins vibrating, immediately stop the tool, release the switch. Some of oil or grease. When working in...
Operators Manual
Page 7
... A PARTICULAR USE OR PURPOSE; interference that MILWAUKEE determines to be free from defects in the Parts & Service sec- notifications regarding your PUNITIVE DAMAGES, OR FOR ANY COSTS, ATTORNEY FEES, authority to , chucks, brushes, cords, saw shoes, blade clamps, o-rings, seals, bumpers, driver blades, pistons, strikers, lifters, and bumper cover washers. *This warranty does not cover Air Nailers & Staplers; Ne pas suivre l'ensemble des règles et instructions peut...
... A PARTICULAR USE OR PURPOSE; interference that MILWAUKEE determines to be free from defects in the Parts & Service sec- notifications regarding your PUNITIVE DAMAGES, OR FOR ANY COSTS, ATTORNEY FEES, authority to , chucks, brushes, cords, saw shoes, blade clamps, o-rings, seals, bumpers, driver blades, pistons, strikers, lifters, and bumper cover washers. *This warranty does not cover Air Nailers & Staplers; Ne pas suivre l'ensemble des règles et instructions peut...
Service Parts List
Page 1
... 2 21 1 NO. Wire Traps or Channels SCREW TORQUE SPECIFICATIONS SEAT TORQUE FIG. WHERE USED (KG/CM) ( IN/LBS) 18 06-82-3002 Housing Cover Head 7-9 6.0-7.8 18 06-82-3002 Housing Cover Grip 7-9 6.0-7.8 MILWAUKEE TOOL l www.milwaukeetool.com 13135 W. NOTE: Damper is no interference when installing the housing covers (20, 21). WHEN ORDERING PARTS M12 FUEL™ Die Grinder CATALOG NO. 2485-20 STARTING SERIAL NO. Lisbon Road...
... 2 21 1 NO. Wire Traps or Channels SCREW TORQUE SPECIFICATIONS SEAT TORQUE FIG. WHERE USED (KG/CM) ( IN/LBS) 18 06-82-3002 Housing Cover Head 7-9 6.0-7.8 18 06-82-3002 Housing Cover Grip 7-9 6.0-7.8 MILWAUKEE TOOL l www.milwaukeetool.com 13135 W. NOTE: Damper is no interference when installing the housing covers (20, 21). WHEN ORDERING PARTS M12 FUEL™ Die Grinder CATALOG NO. 2485-20 STARTING SERIAL NO. Lisbon Road...