Maytag MMV4207JB Support and Manuals
Get Help and Manuals for this Maytag item
View All Support Options Below
Free Maytag MMV4207JB manuals!
Problems with Maytag MMV4207JB?
Ask a Question
Free Maytag MMV4207JB manuals!
Problems with Maytag MMV4207JB?
Ask a Question
Popular Maytag MMV4207JB Manual Pages
Installation Instructions - Page 2
... User Instructions.)
NOTE: Depending on model, aluminum grease filter and charcoal filter may not be included. See the "Venting Design Specifications" section.
2
A
B
C
D
E
FG
H
A. 3/16 - 24 x 3" round-head
Not Shown:
bolts (2) B. 1/4 - 20 x 3" flat-head bolts (2) ■■ Upper cabinet template
C.
MICROWAVE HOOD COMBINATION SAFETY
INSTALLATION REQUIREMENTS
Tools...
Installation Instructions - Page 3
...Rear Wall" part of product will vary slightly depending on door design.
3 Set the cardboard ...9632;■ Support for "Mark Rear Wall" part of any obstructions so that the door can open fully.
■■ Some models have a pocket handle.
See the "Installation Dimensions" ...the heat produced by the microwave oven for use the bump out mounting kit replacing the I bar mounting ...
Installation Instructions - Page 4
... breaker ■■ A separate circuit serving only this microwave oven
GROUNDING INSTRUCTIONS
For all governing codes and ordinances. The microwave oven is properly installed and grounded.
Failure to whether the microwave oven is too short, have a qualified electrician or serviceman install an outlet near the microwave oven.
The plug must be plugged into a grounded 3 prong...
Installation Instructions - Page 5
INSTALLATION INSTRUCTIONS
Remove Mounting Plate
Depending on your model, the mounting plate may be in the foam packaging, or it aside. 3. Tape the microwave oven door closed so that exhaust ports face
the back of the microwave oven. Rotate Blower Motor
The microwave oven is set aside. 3. A
A. Rotate blower motor 180 degree so that the door does
not...
Installation Instructions - Page 6
... slots in Step 1. Damper plate tabs D. Slots
9. Exhaust Port 9.
AB
A.
Damper plate B. Secure damper plate with 2 screws removed in the top of the microwave oven. Repeat Step 1 from "Wall Venting Installation Only." 4.
Reattach damper plate. Damper plate tabs D. Secure damper plate with 2 screws removed in Step 1 at the perforations. Securely tighten screws...
Installation Instructions - Page 7
...
7 See illustrations in "Possible Wall Stud Configurations."
1. Support tabs F. Locate Wall Stud(s)
NOTE: If no wall studs exist within the cabinet opening vertical centerline C. Possible Wall Stud Configurations
These depictions show examples of the wall stud(s) within the opening.
2. Cabinet opening , do not install the microwave oven. See illustrations in "Possible Wall Stud...
Installation Instructions - Page 8
...Installation Only
Upper cabinet bottom
³⁄₈" (1 cm)
4" (10.2 cm)
Centerline
6" (15.2 cm)
6" (15.2 cm)
8. Centerline
2. With the support...bottom edge of the cardboard template or wall template. Set the mounting plate aside.
NOTES: ■■ ...upper cabinet.
9. Rear wall B.
Mark Rear Wall
The microwave oven must align with front edge of cabinet. Using measuring...
Installation Instructions - Page 9
..." section.
2. Insert lag screw(s) into the hole(s) drilled into the remaining end hole. 6. Check alignment of "Installation for Wall Stud at the other hole drilled in Step 2 of the "Mark Rear Wall."
2. With the support tabs of the mounting plate facing forward, insert a 3/16-24 x 3" round-head bolt through the wall at...
Installation Instructions - Page 10
... around the supply cord hole as installed) has a partial wall covering (for example, tile backsplash), be sure the "Rear Wall" arrows align to the thickest part of t he rear wall (for... on the template is metal, the supply cord bushing needs to use as guides.
■■ If the wall behind the microwave oven (as shown. Secure damper assembly with the vertical centerline on the template...
Installation Instructions - Page 11
... using the microwave oven. Remove the 2 packing spacers from the top of the microwave oven is the heavy side. Place a washer on your model, it does...support tabs at the bottom of mounting plate, and set aside on a covered surface. 9. A
B A. Make sure the microwave oven door is required, rotate microwave oven downward. NOTE: If microwave oven does not need to move and install microwave...
Installation Instructions - Page 12
... cord.
The installation is not positioned as shown. A
B
C
D
E
F
A. Damper plate
Electrical Shock Hazard
Plug into grounded 3 prong outlet. 3. NOTE: Avoid damage to the mounting nut, screw the bolts into a grounded 3 prong outlet.
■■ See the User Instructions for troubleshooting information. Do not use an adapter. Check the operation of microwave oven by placing...
Installation Instructions - Page 13
... metal vent.
■■ Using the most direct route by minimizing the length of the vent and number of the microwave oven and the transition piece. A
B
C
D
E
3" (7.6 cm)
F
A. diameter round vent C. Wall cap...
■■ Not installing 2 elbows together, for architectural designer and builder/ contractor reference only. VENTING DESIGN SPECIFICATIONS
This section is proper ...
Installation Instructions - Page 14
For best performance, use when installing this microwave oven in the User Guide. If you need your authorized dealer or service center for details.
14 The filler panels come in the User Guide.
You will need , add the equivalent lengths of available replacement parts.
Replacement Parts
If any of the microwave oven. ASSISTANCE
Call your dealer to -round transition piece =...
Maytag MMV4207JB Reviews
We have not received any reviews for Maytag yet.