Installation Guide
Page 4
... without riser Parts supplied (steam models): Tin snips (new vent installations) 1/4"( 6 mm) nut driver (recommended) Tape measure Pliers 4 "Y" connector 2' (0.6 m) inlet hose 5' (1.52 m) Inlet Hose Rubber washer Remove parts package from whom you purchased your "Use and Care Guide." Check existing electrical supply and venting. See "Electrical Requirements" and "Venting Requirements" before...
... without riser Parts supplied (steam models): Tin snips (new vent installations) 1/4"( 6 mm) nut driver (recommended) Tape measure Pliers 4 "Y" connector 2' (0.6 m) inlet hose 5' (1.52 m) Inlet Hose Rubber washer Remove parts package from whom you purchased your "Use and Care Guide." Check existing electrical supply and venting. See "Electrical Requirements" and "Venting Requirements" before...
Installation Guide
Page 5
...; A location allowing for your local building inspector. See "Electrical Requirements." ■■ Floor must not be installed or stored in longer drying times. Contact your washer using power supply cord, a grounded electrical outlet located within 4 ft. (1.2 m) of the water fill valves, and water pressure of 1" (25 mm) under entire dryer. Models...
...; A location allowing for your local building inspector. See "Electrical Requirements." ■■ Floor must not be installed or stored in longer drying times. Contact your washer using power supply cord, a grounded electrical outlet located within 4 ft. (1.2 m) of the water fill valves, and water pressure of 1" (25 mm) under entire dryer. Models...
Installation Guide
Page 12
... 2 Rigid metal 44 ft. (13.4 m) 38 ft. (11.6 m) 3 Rigid metal 35 ft. (10.7 m) 29 ft. (8.8 m) 4 Rigid metal 27 ft. (8.2 m) 21 ft. (6.4 m) Maytag Vent System Chart Number of 90° elbows Type of dryer. ■■ Reduce performance, resulting in longer drying times and increased energy usage. Connect... INLET HOSES For non-steam models, skip to seal all joints. Use clamps to "Connect Vent." Check and see if rubber washer is a registered trademark of elbows and turns. ■■ When using straightest path possible. The dryer must fit over the exhaust...
... 2 Rigid metal 44 ft. (13.4 m) 38 ft. (11.6 m) 3 Rigid metal 35 ft. (10.7 m) 29 ft. (8.8 m) 4 Rigid metal 27 ft. (8.2 m) 21 ft. (6.4 m) Maytag Vent System Chart Number of 90° elbows Type of dryer. ■■ Reduce performance, resulting in longer drying times and increased energy usage. Connect... INLET HOSES For non-steam models, skip to seal all joints. Use clamps to "Connect Vent." Check and see if rubber washer is a registered trademark of elbows and turns. ■■ When using straightest path possible. The dryer must fit over the exhaust...
Installation Guide
Page 13
... overtighten. Screw on coupling by hand until it is seated on . 7. 2. See figure A. Screw on coupling by hand until it is seated on connector. 3. Attach washer cold inlet hose to other end of dryer back panel. NOTE: Do not overtighten. Attach long hose to fill valve at bottom of long hose...
... overtighten. Screw on coupling by hand until it is seated on . 7. 2. See figure A. Screw on coupling by hand until it is seated on connector. 3. Attach washer cold inlet hose to other end of dryer back panel. NOTE: Do not overtighten. Attach long hose to fill valve at bottom of long hose...