Installation Guide
Page 4
... parts. Check existing electrical supply and venting. Parts needed (steam models): Utility knife Tin snips (new vent installations) 2' (0.6 m) inlet hose 5' (1.52 m) inlet hose and rubber washer Caulking gun and compound Adjustable wrench that all models): Flat-blade screwdriver #2 Phillips screwdriver Leveling legs (4) Parts supplied (steam models): 1/4" and 5/16" nut driver (recommended...
... parts. Check existing electrical supply and venting. Parts needed (steam models): Utility knife Tin snips (new vent installations) 2' (0.6 m) inlet hose 5' (1.52 m) inlet hose and rubber washer Caulking gun and compound Adjustable wrench that all models): Flat-blade screwdriver #2 Phillips screwdriver Leveling legs (4) Parts supplied (steam models): 1/4" and 5/16" nut driver (recommended...
Installation Guide
Page 5
... view: * Approx. See "Venting Requirements". 5 See "Venting Requirements." ■■A separate 15 or 20 amp circuit for a gas dryer or 30 amp circuit for your washer using a pedestal, you will need : ■■A location allowing for exhaust vent with maximum slope of 5" (127 mm) clearance behind dryer for proper exhaust installation...
... view: * Approx. See "Venting Requirements". 5 See "Venting Requirements." ■■A separate 15 or 20 amp circuit for a gas dryer or 30 amp circuit for your washer using a pedestal, you will need : ■■A location allowing for exhaust vent with maximum slope of 5" (127 mm) clearance behind dryer for proper exhaust installation...
Installation Guide
Page 12
... hoses if bulges, kinks, cuts, wear, or leaks are found. 1. Turn cold water off, remove hose, and replace rubber washer Turn cold water faucet off and remove washer inlet hose. Avoid 90° turns. Use clamps to male end of the 2 ft (0.6 m) inlet hose. Vent must be ... lint. 2. Attach short hose and "Y" connector Attach 2 ft (0.6 m) inlet hose to the cold water faucet using straightest path possible. Remove old rubber washer from inlet hose and replace with 4" (102 mm) clamp. Then attach "Y" connector to seal all joints. Connect vent to exhaust hood CONNECT INLET HOSE ...
... hoses if bulges, kinks, cuts, wear, or leaks are found. 1. Turn cold water off, remove hose, and replace rubber washer Turn cold water faucet off and remove washer inlet hose. Avoid 90° turns. Use clamps to male end of the 2 ft (0.6 m) inlet hose. Vent must be ... lint. 2. Attach short hose and "Y" connector Attach 2 ft (0.6 m) inlet hose to the cold water faucet using straightest path possible. Remove old rubber washer from inlet hose and replace with 4" (102 mm) clamp. Then attach "Y" connector to seal all joints. Connect vent to exhaust hood CONNECT INLET HOSE ...
Installation Guide
Page 13
Tighten couplings 5. Attach long hose to dryer fill valve and tighten coupling Using pliers, tighten the couplings with additional two-thirds turn . Attach washer cold inlet hose to the coupling can result. Damage to other end of the 5 ft (1.5 m) inlet hose ends to the coupling can result. 4. Turn on ...
Tighten couplings 5. Attach long hose to dryer fill valve and tighten coupling Using pliers, tighten the couplings with additional two-thirds turn . Attach washer cold inlet hose to the coupling can result. Damage to other end of the 5 ft (1.5 m) inlet hose ends to the coupling can result. 4. Turn on ...
Use & Care Guide
Page 4
... the dryer to be installed on options and ordering, contact your new washer and dryer with the following genuine Maytag accessories. The large drawer provides convenient storage. Worksurface The worksurface bridges the washer and dryer, and provides a convenient working height. ACCESSORIES Customize your dealer..., call 1-800-807-6777, or visit: www.maytag.ca 15" Pedestal Color-matched pedestals raise the washer and dryer to a more information on top of the washer. For more comfortable working and storage area. 4 Stack Kit If space is ...
... the dryer to be installed on options and ordering, contact your new washer and dryer with the following genuine Maytag accessories. The large drawer provides convenient storage. Worksurface The worksurface bridges the washer and dryer, and provides a convenient working height. ACCESSORIES Customize your dealer..., call 1-800-807-6777, or visit: www.maytag.ca 15" Pedestal Color-matched pedestals raise the washer and dryer to a more information on top of the washer. For more comfortable working and storage area. 4 Stack Kit If space is ...