Use & Care Guide
Page 4
... provides a convenient working height. ACCESSORIES Customize your dealer, call 1-800-807-6777, or visit: www.maytag.ca. 15" Pedestal Color-matched pedestals raise the washer and dryer to be installed on options and ordering, contact your new washer and dryer with the following genuine Maytag® accessories.For more comfortable working and storage area.
... provides a convenient working height. ACCESSORIES Customize your dealer, call 1-800-807-6777, or visit: www.maytag.ca. 15" Pedestal Color-matched pedestals raise the washer and dryer to be installed on options and ordering, contact your new washer and dryer with the following genuine Maytag® accessories.For more comfortable working and storage area.
Installation Guide
Page 1
... 15 Install Vent System 16 CONNECT INLET HOSE 17 CONNECT VENT 18 LEVEL DRYER 19 COMPLETE INSTALLATION CHECKLIST 19 DOOR REVERSAL KIT (OPTIONAL 20 STACKING WASHER AND DRYER (OPTIONAL 20 TROUBLESHOOTING 20 Para una version de estas instrucciones en español, visite www.Whirlpool.com INSTALLATION NOTES Date of purchase...
... 15 Install Vent System 16 CONNECT INLET HOSE 17 CONNECT VENT 18 LEVEL DRYER 19 COMPLETE INSTALLATION CHECKLIST 19 DOOR REVERSAL KIT (OPTIONAL 20 STACKING WASHER AND DRYER (OPTIONAL 20 TROUBLESHOOTING 20 Para una version de estas instrucciones en español, visite www.Whirlpool.com INSTALLATION NOTES Date of purchase...
Installation Guide
Page 3
... a UL listed power supply cord kit marked for installing new exhaust vent) Short inlet hose (steam models only) Long inlet hose (steam models only) Rubber washers (steam models only) Optional Equipment: (Not supplied with a pedestal or a stack kit.
... a UL listed power supply cord kit marked for installing new exhaust vent) Short inlet hose (steam models only) Long inlet hose (steam models only) Rubber washers (steam models only) Optional Equipment: (Not supplied with a pedestal or a stack kit.
Installation Guide
Page 4
...; C). LOCATION REQUIREMENTS Check code requirements. You may use the water supply for walls, doors, and floor moldings. spacing for companion appliances and clearances for your washer using power supply cord, a grounded electrical outlet located within 4 ft. (1.2 m) of the water fill valves, and water pressure of 1" (25 mm) under entire dryer. Some...
...; C). LOCATION REQUIREMENTS Check code requirements. You may use the water supply for walls, doors, and floor moldings. spacing for companion appliances and clearances for your washer using power supply cord, a grounded electrical outlet located within 4 ft. (1.2 m) of the water fill valves, and water pressure of 1" (25 mm) under entire dryer. Some...
Installation Guide
Page 5
...) 1" (25 mm) 1" (25 mm) Custom under counter installation (dryer only): 5" (127 mm) 3" (76 mm) 24 in.2 (155 cm2) 1" (25 mm) 1" (25 mm) Closet Installation (stacked washer and dryer): 6" (152 mm) 3" (76 mm) 76" (1930 mm) 48 in.2 (310 cm2) 5" (127 mm) 1" (25 mm) 3" (76 mm) 24 in your dealer. Openings (such...
...) 1" (25 mm) 1" (25 mm) Custom under counter installation (dryer only): 5" (127 mm) 3" (76 mm) 24 in.2 (155 cm2) 1" (25 mm) 1" (25 mm) Closet Installation (stacked washer and dryer): 6" (152 mm) 3" (76 mm) 76" (1930 mm) 48 in.2 (310 cm2) 5" (127 mm) 1" (25 mm) 3" (76 mm) 24 in your dealer. Openings (such...
Installation Guide
Page 17
...hose to male end of hose failure. Record hose installation or replacement dates on connector. NOTE: Do not overtighten. Check and see if rubber washer is seated on connector. If "Y" connector cannot be attached directly to the cold water faucet, the short hose must be used. See figure...can result. 17 Damage to "Y" connector and tighten couplings Turn cold water faucet off , remove hose, and replace rubber washer Using pliers, tighten the couplings with new rubber washer provided. 2. One end of the "Y" connector to cold water faucet. Screw on coupling by hand until it is ...
...hose to male end of hose failure. Record hose installation or replacement dates on connector. NOTE: Do not overtighten. Check and see if rubber washer is seated on connector. If "Y" connector cannot be attached directly to the cold water faucet, the short hose must be used. See figure...can result. 17 Damage to "Y" connector and tighten couplings Turn cold water faucet off , remove hose, and replace rubber washer Using pliers, tighten the couplings with new rubber washer provided. 2. One end of the "Y" connector to cold water faucet. Screw on coupling by hand until it is ...
Installation Guide
Page 20
...section in your "Use and Care Guide" or visit our website and reference Frequently Asked Questions to possibly avoid the cost of a service call. STACKING WASHER AND DRYER (OPTIONAL) If you prefer to reverse the door swing on your dryer: A door reversal kit, Part Number W10406955 is available to order.... DOOR REVERSAL (OPTIONAL) If you prefer to stack your washer and dryer: A stack kit, Part Number 8572546, is available to order. SP © 2011 All rights reserved 06/11 Printed in your "Use ...
...section in your "Use and Care Guide" or visit our website and reference Frequently Asked Questions to possibly avoid the cost of a service call. STACKING WASHER AND DRYER (OPTIONAL) If you prefer to reverse the door swing on your dryer: A door reversal kit, Part Number W10406955 is available to order.... DOOR REVERSAL (OPTIONAL) If you prefer to stack your washer and dryer: A stack kit, Part Number 8572546, is available to order. SP © 2011 All rights reserved 06/11 Printed in your "Use ...