Owners Manual
Page 4
... dryer, and provides a convenient working height. ACCESSORIES Customize your dealer, or visit: www.maytag.com. 15" Pedestal Color matched pedestals raise the washer and dryer to be installed on top of the washer. 4 For more comfortable working and storage area. Available in matching colors. The large drawer provides convenient storage. Stack Kit If...
... dryer, and provides a convenient working height. ACCESSORIES Customize your dealer, or visit: www.maytag.com. 15" Pedestal Color matched pedestals raise the washer and dryer to be installed on top of the washer. 4 For more comfortable working and storage area. Available in matching colors. The large drawer provides convenient storage. Stack Kit If...
Installation Instructions
Page 3
...;■Vent clamps ■■Vent elbows and ductwork Additional parts may be at least 4 ft. (1.22 m) long. Short inlet hose Long inlet hose Rubber washer Optional Equipment: (Not supplied with upturned ends. ■■A UL listed strain relief. 1/4" and 5/16" nut driver (recommended) Adjustable wrench that opens to your installation...
...;■Vent clamps ■■Vent elbows and ductwork Additional parts may be at least 4 ft. (1.22 m) long. Short inlet hose Long inlet hose Rubber washer Optional Equipment: (Not supplied with upturned ends. ■■A UL listed strain relief. 1/4" and 5/16" nut driver (recommended) Adjustable wrench that opens to your installation...
Installation Instructions
Page 4
... code requirements. Side view: 507/8" (1292 mm) 305/8" (728 mm) Back view: NOTE: Most installations require a minimum of 5" (127 mm) clearance behind dryer for your washer using a pedestal, you will need 18" (460 mm) to bottom of 1" (25 mm) under entire dryer. LOCATION REQUIREMENTS Check code requirements. DRYER DIMENSIONS Front view...
... code requirements. Side view: 507/8" (1292 mm) 305/8" (728 mm) Back view: NOTE: Most installations require a minimum of 5" (127 mm) clearance behind dryer for your washer using a pedestal, you will need 18" (460 mm) to bottom of 1" (25 mm) under entire dryer. LOCATION REQUIREMENTS Check code requirements. DRYER DIMENSIONS Front view...
Installation Instructions
Page 15
... on coupling by hand until it is seated on the hoses for future reference. Vent must be attached directly to exhaust hood with new rubber washer provided. See figure A. Install exhaust hood 12" min. (305 mm) 12" min. (305 mm) Install exhaust hood and use duct tape, screws, or ... bulges, kinks, cuts, wear, or leaks are found. 1. Turn cold water off, remove hose, and replace rubber washer Turn cold water faucet off and remove washer inlet hose. Check and see if rubber washer is in the "Y" connector. Attach short hose to male end of use old hoses. Remove old rubber...
... on coupling by hand until it is seated on the hoses for future reference. Vent must be attached directly to exhaust hood with new rubber washer provided. See figure A. Install exhaust hood 12" min. (305 mm) 12" min. (305 mm) Install exhaust hood and use duct tape, screws, or ... bulges, kinks, cuts, wear, or leaks are found. 1. Turn cold water off, remove hose, and replace rubber washer Turn cold water faucet off and remove washer inlet hose. Check and see if rubber washer is in the "Y" connector. Attach short hose to male end of use old hoses. Remove old rubber...
Installation Instructions
Page 16
... . Damage to other end of long hose to dryer fill valve and tighten coupling A Using pliers, tighten the couplings with additional two-thirds turn. Attach washer cold inlet hose to the coupling can result. Check for leaks Check for leaks around "Y" connector, faucet, and hoses. 16 Using pliers, tighten the couplings...
... . Damage to other end of long hose to dryer fill valve and tighten coupling A Using pliers, tighten the couplings with additional two-thirds turn. Attach washer cold inlet hose to the coupling can result. Check for leaks Check for leaks around "Y" connector, faucet, and hoses. 16 Using pliers, tighten the couplings...