Specification Sheet
Page 1
... Certifications ADA Compliant Yes ENERGY STAR® Certified Yes Key Features & Benefits Extra Power Button The Extra Power button boosts drying power on select Maytag® washers to get clothes ready in the U.S.A. All rights reserved. For complete details, see Installation Instructions packed with Door Open 90° 12 Bulky ...& Care Guide Warranty *Results may vary based on the Drive Motor and Drum American Pride 7.3 cu. 7.3 cu. Front Load Electric Dryer MED6630H Chrome Shadow MED6630HC Also available in: White MED6630HW Capacity Total 7.3 cu. ft. D200104XXD.
... Certifications ADA Compliant Yes ENERGY STAR® Certified Yes Key Features & Benefits Extra Power Button The Extra Power button boosts drying power on select Maytag® washers to get clothes ready in the U.S.A. All rights reserved. For complete details, see Installation Instructions packed with Door Open 90° 12 Bulky ...& Care Guide Warranty *Results may vary based on the Drive Motor and Drum American Pride 7.3 cu. 7.3 cu. Front Load Electric Dryer MED6630H Chrome Shadow MED6630HC Also available in: White MED6630HW Capacity Total 7.3 cu. ft. D200104XXD.
Installation Instructions
Page 4
...) and 5/16" (8 mm) nut driver (recommended) Level Pipe-joint compound resistant to 1" (25 mm) or hex-head socket wrench Wire stripper (direct wire installations) 4 Rubber washer 5' (1.52 m) inlet hose Parts package is located in dryer drum. Check that all models): Tape measure Pliers Utility knife Tin snips (new vent installations) Leveling...
...) and 5/16" (8 mm) nut driver (recommended) Level Pipe-joint compound resistant to 1" (25 mm) or hex-head socket wrench Wire stripper (direct wire installations) 4 Rubber washer 5' (1.52 m) inlet hose Parts package is located in dryer drum. Check that all models): Tape measure Pliers Utility knife Tin snips (new vent installations) Leveling...
Installation Instructions
Page 5
...; For garage installation, place dryer at end of automatic sensor cycles, resulting in longer drying times. *Approx. Contact your washer's water supply by purchasing the necessary parts noted in garages, closets, mobile homes, or sleeping quarters. If slope is greater...Level floor with upturned ends. ■■ A UL Listed strain relief. Read "Electrical Requirements" and "Venting Requirements" before purchasing parts. Maytag® Models IMPORTANT: Do not operate, install, or store dryer where it will need : ■■ A location allowing for your installation...
...; For garage installation, place dryer at end of automatic sensor cycles, resulting in longer drying times. *Approx. Contact your washer's water supply by purchasing the necessary parts noted in garages, closets, mobile homes, or sleeping quarters. If slope is greater...Level floor with upturned ends. ■■ A UL Listed strain relief. Read "Electrical Requirements" and "Venting Requirements" before purchasing parts. Maytag® Models IMPORTANT: Do not operate, install, or store dryer where it will need : ■■ A location allowing for your installation...
Installation Instructions
Page 21
... other side of the 2 ft. (0.6 m) inlet hose. Tighten couplings 1. Screw on coupling by hand until it is seated on faucet. Attach washer cold inlet hose to reduce the risk of hose failure. NOTE: Replace inlet hoses after 5 years of the 5 ft. (1.5 m) inlet hose ... 3. Damage to the "Y" connector. Damage to male end of "Y" connector. Then attach "Y" connector to the coupling can result. 4. Remove old rubber washer from inlet hose and replace with additional 2/3 turn . Attach short hose and "Y" connector Attach one of use old hoses. NOTE: Do not overtighten. ...
... other side of the 2 ft. (0.6 m) inlet hose. Tighten couplings 1. Screw on coupling by hand until it is seated on faucet. Attach washer cold inlet hose to reduce the risk of hose failure. NOTE: Replace inlet hoses after 5 years of the 5 ft. (1.5 m) inlet hose ... 3. Damage to the "Y" connector. Damage to male end of "Y" connector. Then attach "Y" connector to the coupling can result. 4. Remove old rubber washer from inlet hose and replace with additional 2/3 turn . Attach short hose and "Y" connector Attach one of use old hoses. NOTE: Do not overtighten. ...
Instruction Sheet
Page 1
...whom you purchased your dryer or an authorized service company. 2' (0.6 m) Inlet hose CONNECT INLET HOSES 1. Turn cold water faucet off and remove washer inlet hose. 7. Using pliers, tighten the couplings an additional two-thirds turn . Screw on coupling by hand until it is seated on . ...11. Damage to cold water faucet. The dryer must be sure rubber washers are on fill valve connector. 4. Using pliers, tighten the couplings with dryer) 5' (1.5 m) Inlet Hose Your installation may require additional parts....
...whom you purchased your dryer or an authorized service company. 2' (0.6 m) Inlet hose CONNECT INLET HOSES 1. Turn cold water faucet off and remove washer inlet hose. 7. Using pliers, tighten the couplings an additional two-thirds turn . Screw on coupling by hand until it is seated on . ...11. Damage to cold water faucet. The dryer must be sure rubber washers are on fill valve connector. 4. Using pliers, tighten the couplings with dryer) 5' (1.5 m) Inlet Hose Your installation may require additional parts....