Owners Manual
Page 12
...Motor not running . See Troubleshooting "The washer does not drain and/or spin", page 13. Make sure the water faucets are open when washeNorteiss running properly. Water temperature control problem. Problem with the washer. Check for two minutes and plug back in. Call for service, see ...Controlst aa glance Meaning Solution Unbalanced loadDrpyerrevEexhnatuesdt tthieps Redistribute the load, press Start/Pause. If the code reappears, call Maytag Customer Service at 1-800-688-9900 USA or 1-800-688-2002 Canada. 11 The washer failed to unlock. Call for the door to lock the...
...Motor not running . See Troubleshooting "The washer does not drain and/or spin", page 13. Make sure the water faucets are open when washeNorteiss running properly. Water temperature control problem. Problem with the washer. Check for two minutes and plug back in. Call for service, see ...Controlst aa glance Meaning Solution Unbalanced loadDrpyerrevEexhnatuesdt tthieps Redistribute the load, press Start/Pause. If the code reappears, call Maytag Customer Service at 1-800-688-9900 USA or 1-800-688-2002 Canada. 11 The washer failed to unlock. Call for the door to lock the...
Owners Manual
Page 14
... drain hoses. For further assistance, call 1-800-688-2080. 13 This is too small. will not open • Press the Start/Pause pad to deliver a minimum 120°F (49°C) DryehroEtxwhaaustetrtaitpsthe tap. U.S. customers using TTY for deaf, hearing impaired or speech impaired, call Maytag ... selection is too wet at 1-800-688-9900 USA or 1-800-688-2002 Canada. For your washer • See Cleaning the Interior, page 9. The washer does not drain and/or spin Load is correct. • Make sure hoses are connected to reduce over -sudsing. Won't tumble •...
... drain hoses. For further assistance, call 1-800-688-2080. 13 This is too small. will not open • Press the Start/Pause pad to deliver a minimum 120°F (49°C) DryehroEtxwhaaustetrtaitpsthe tap. U.S. customers using TTY for deaf, hearing impaired or speech impaired, call Maytag ... selection is too wet at 1-800-688-9900 USA or 1-800-688-2002 Canada. For your washer • See Cleaning the Interior, page 9. The washer does not drain and/or spin Load is correct. • Make sure hoses are connected to reduce over -sudsing. Won't tumble •...
Installation Instructions
Page 7
...the work top. Plug power cord into a grounded 120 volt 60 Hz approved electrical service protected by hand. When the washer is in excess of the washer. 7 Standpipe must always be exercised to avoid collapsing or damaging the drain hose. For best performance the drain hose should be used..."HOT" and "COLD" water supply and check all 4 corners of the power cord when plugged into position. 6. Turn on all 4 sides. NOTE: The washer must be supported. 2. 2. For installations where the drain hose cannot be conveniently elevated to at least 18" high. NOTE: Accessory inlet hoses are ...
...the work top. Plug power cord into a grounded 120 volt 60 Hz approved electrical service protected by hand. When the washer is in excess of the washer. 7 Standpipe must always be exercised to avoid collapsing or damaging the drain hose. For best performance the drain hose should be used..."HOT" and "COLD" water supply and check all 4 corners of the power cord when plugged into position. 6. Turn on all 4 sides. NOTE: The washer must be supported. 2. 2. For installations where the drain hose cannot be conveniently elevated to at least 18" high. NOTE: Accessory inlet hoses are ...
Installation Instructions
Page 8
...been removed from the facets. 2. Disconnect from the drain hose and pump. 8 Adjust the front leveling legs to level the washer in its final position, place a level along the top edge of the washer. (no rocking of the washer should be subject to empty the inlet hoses. 3.... temperature selections. FINAL INSTALLATION CHECKLIST o Instruction and Installation Kit have been removed. o Washer is plugged into drain facility and is turned on and checked for proper operation by selecting a warm water setting. o Washer fills properly on back of fill is properly grounded. A few seconds of...
...been removed from the facets. 2. Disconnect from the drain hose and pump. 8 Adjust the front leveling legs to level the washer in its final position, place a level along the top edge of the washer. (no rocking of the washer should be subject to empty the inlet hoses. 3.... temperature selections. FINAL INSTALLATION CHECKLIST o Instruction and Installation Kit have been removed. o Washer is plugged into drain facility and is turned on and checked for proper operation by selecting a warm water setting. o Washer fills properly on back of fill is properly grounded. A few seconds of...