Makita XT453T Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita XT453T manuals!
Problems with Makita XT453T?
Ask a Question
Free Makita XT453T manuals!
Problems with Makita XT453T?
Ask a Question
Popular Makita XT453T Manual Pages
XDT14 Instruction Manual - Page 6
... brake
This tool is released, have the tool serviced at a Makita service center. Be careful not to change the direction of... the lamp.
To turn off the lamp status, first pull and release the switch trigger. Reversing switch lever
CAUTION: Always check the direction of lamp, or it . CAUTION: When not operating the tool, always set...
XDT14 Instruction Manual - Page 10
... USE OF THE PRODUCT. This Warranty gives you specific legal rights, and you need any assistance for use of any trouble develop during this manual.
THIS DISCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY. The use with your local Makita Service Center. • Driver bits • Socket bits • Hook • Plastic...
XDT14 Parts Breakdown - Page 2
... PIN 5 THIN WASHER 15 INTERNAL GEAR 51 O RING 40 BEARING BOX COMPLETE HOUSING SET RUBBER PIN 6 HEX. Model XDT14M/R/Z Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part#
Description
001
183E36-5
001 C10 263005-3
001 C20 252126-6
001 D10
002
852L15-3...
041 D10
042
809R92-2
A01
266622-8
A02
346449-3
A03
450128-8
A04
***DC18RC
HOUSING SET RUBBER PIN 6 HEX.
XRJ05 Instruction Manual - Page 3
... the safety of dust extraction and collection facilities, ensure these instructions, taking into account the working conditions and the work by a qualified repair person using only identical replacement parts. Disconnect the plug from the power source and/or the battery pack from moving parts, breakage of parts and any other battery packs may create a risk of...
XRJ05 Instruction Manual - Page 8
... the trouble is thoroughly inspected and tested before attempting to protect your local Makita Service Center. • Recipro saw blade into light contact with the workpiece. NOTE: If you remove the recipro saw blade without charge. In this case, rotate the blade clamp lever fully again, then make a pilot groove using Makita replacement parts...
Makita DC18RC Instruction Manual - Page 3
...into charger until it to the guide of injury, charge only MAKITA ...a sharp blow, been dropped, or otherwise dam- ENGLISH
Specifications
Model Input Output Weight
DC18RA
DC18RC
A.C. 120 V 50 -...service center to replace it within another five seconds after this , the melody sound changes in a risk of completed charging. 2. This manual contains important safety and operating instructions...
DML815 Instruction Manual - Page 6
...manual.
Hook
The hook is not available, refer to the warranty details set forth at below website for your respective country. United States of the hook can be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts... maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be installed on the upper or lower ring...
DML815 Parts Breakdown - Page 2
Model DML815/B Parts Lisrt
A = Standard Equipment 〇= Circuit Diagram
Item#
Part#
Description
Q'ty Unit
001
GM00001299
002
...HOUSING ASSY BLACK SCREW 3 X 12PB B0130120702 LOCKING SHAFT(C4120802001) COMPRESSION SPRING B1303802922 HOUSING L/R(G0180200400) HOUSING L/R SET BLACK RING (B3103184009) HOOK PLATE(B2804802921) SCREW 3 X 12PB B0130120702 MAIN PCBA ASSY INC. 15 BATTERY HOLDER C2010239007 ...
XPH14 Instruction Manual - Page 2
.... WARNING: Only use reduces the risk of electric shock.
4. ENGLISH (Original instructions)
SPECIFICATIONS
Model: Drilling capacities
Fastening capacities No load speed (RPM) Blows per minute Overall length.../2014, are subject to change without notice.
• Specifications may differ from heat, oil, sharp edges or moving parts. Use of electric shock.
5. Power tool plugs must ...
XPH14 Instruction Manual - Page 4
... cartridge to follow the safety rules stated in this instruction manual may result in a fire, excessive heat, or explosion.
3.
MISUSE or failure to water or rain. Keep hands away from repeated use pliers to noise can cause personal injury.
3.
Safety instructions when using only identical replacement parts. At higher speeds, the bit is likely to...
XPH14 Instruction Manual - Page 5
...item being inserted correctly. Unless the tool supports the use near high-voltage electrical power ...cartridge. Charge the battery cartridge before installing or removing of the battery cartridge. ...hot battery cartridges.
15. SAVE THESE INSTRUCTIONS. 10. The contained lithium-ion batteries ...from children. Overcharging shortens the battery service life.
3. Charge the battery cartridge ...
XPH14 Instruction Manual - Page 8
...tool.
Align the graduations with the ring positioned halfway between the graduations. pine)
Hard wood (e.g. NOTICE: Always set the ring correctly to determine which torque level is required for a particular application. NOTICE: Do not change the... difficulty to " ", it may be damaged. Installing or removing driver bit/ drill bit
Optional accessory
1 3
2
► 1 . Close 3.
XPH14 Instruction Manual - Page 10
...a vise or similar hold it may be removed simply by setting the reversing switch to reverse rotation in the screw head, or the screw and/or driver bit may back out abruptly if you do not hold ... to the proper torque level for your drill bit, decrease the tool performance and shorten the service life of the driver bit in . CAUTION: Hold the tool firmly and exert care when the drill bit begins ...
XPH14 Instruction Manual - Page 11
...local Makita Service Center. • Drill bits • Driver bits •... and RELIABILITY, repairs, any other ...set forth at the point to be drilled.
Only use gasoline, benzine, thinner, alcohol or the like. If you need any assistance for its stated purpose. The guide screw makes drilling easier by Makita Authorized or Factory Service Centers, always using Makita replacement parts...
XT453T New Tool Flyer English - Page 1
...SPECIFICATIONS
Tool Count 4 Voltage 18V Battery 18V LXT® Lithium-Ion Battery Charge Time (minutes 45 UPC Code 088381-729277
STANDARD EQUIPMENT
• 18V LXT® Brushless 1/2" Hammer Driver-Drill (XPH14Z) • 18V LXT® Brushless 3-Speed Impact Driver... integrated L.E.D. NTF-0121 MA-9688-19
makitatools.com Impact Bit Set (E-01644) 5. Flashlight (DML815) • 2 18V LXT&#...
Makita XT453T Reviews
We have not received any reviews for Makita yet.