Makita XSL01Z Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita XSL01Z manuals!
Problems with Makita XSL01Z?
Ask a Question
Free Makita XSL01Z manuals!
Problems with Makita XSL01Z?
Ask a Question
Popular Makita XSL01Z Manual Pages
XSL01Z Instruction Manual - Page 2
...blade 190 mm (7-1/2") in working order. 3. Cluttered areas and benches invite accidents.
(For All Tools)
2 ENGLISH (Original instructions)
SPECIFICATIONS
Model Blade diameter Hole (arbor) diameter Max.
KEEP GUARDS IN PLACE and in diameter. Read the owner's manual carefully. Bevel angle Max.
KNOW YOUR POWER TOOL. REMOVE ADJUSTING KEYS AND WRENCHES. Miter angle Max. Cutting...
XSL01Z Instruction Manual - Page 3
...guide fence with the charger specified by a qualified repair person using your power tool serviced...parts, breakage of injury to slide compound saw blade. MAKE WORKSHOP KID PROOF with specifically...other metal objects like .
16. Follow instructions for best and safest performance. when ... parts, mounting, and any coasting blade. Consult the owner's manual...replace strict adherence to persons.
18...
XSL01Z Instruction Manual - Page 4
... blade carefully for this instruction manual may cause an injury....installation or a poorly balanced blade.
25. Take caution to damage the arbor, flanges (especially the installing...before changing blade or servicing. 8. Wait until the... it run for kickback. Replace cracked or damaged blade immediately...parts could result in the base to be toxic. all moving workpiece or changing settings...
XSL01Z Instruction Manual - Page 5
...level and stable surface using battery cartridge, read all instructions and cautionary markings on the
supporting surface. Overcharging shortens the battery service life.
3. This tool should be bolted with two... the battery cartridge even if it comes into your eyesight. 5. SAVE THESE INSTRUCTIONS. INSTALLATION
Bench mounting When the tool is shipped, the handle is completely worn out....
XSL01Z Instruction Manual - Page 7
...service center for proper operation follow the steps below the top surface of the turn base at the point where the front face of the guide...of the kerf boards will help provide proper support of
2
blade
3. Straight cut
3
4
...right) securing the kerf boards. When installing a new blade, always check the ... teeth 3. NOTICE: • After setting the bevel angle ensure that the
kerf...
XSL01Z Instruction Manual - Page 9
... at a Makita service center.
1
1. Switch action
Electric brake
This tool is not a substitute for insertion of the wrench holder. To start up of repair may result in serious... button and pull the switch trigger. Return tool to switch off button
CAUTION:
2
2. Installing or removing saw blade
1.
Accidental start the tool, press in serious personal injury. Hex wrench...
XSL01Z Instruction Manual - Page 11
... secure it has come to do so may move during all the way. Proper workpiece support will help avoid blade pinch and possible kickback which can be thrown, cause damage to keep...
If some part contacts the vise, re-position the vise. WARNING: • The workpiece must be installed in two positions on the
opposite side of a coasting blade may result in the guide fence or ...
XSL01Z Instruction Manual - Page 16
Compound Miter Saw Miter and Bevel Angle Settings
Ceiling
52°
38°
Wall
Wall to Crown Molding Angle: 52/38 degrees
Wall Angle Bevel Angle Miter Angle
(deg.)
(deg.)
(deg.)
60 43.0
...
XSL01Z Instruction Manual - Page 17
Wood facing
Use of wood facing helps to assure splinter-free cuts in the guide fence. Compound Miter Saw Miter and Bevel Angle Settings
Ceiling
45°
45°
Wall
Wall to the guide fence using the holes in workpieces. Attach a wood facing to Crown Molding Angle: 45 degrees
Wall Angle Bevel Angle Miter...
XSL01Z Instruction Manual - Page 18
... not attempt to 385 mm (15-1/8"), use of the holder-rod assembly (optional
accessory) allows cutting repetitive lengths up to the
guide fence. WARNING: • Use screws to attach the wood facing to 2,200 mm (7.2ft) approximately.
9. Install the set plate out of control and serious personal injury. NOTE: • Use of the...
XSL01Z Instruction Manual - Page 20
...and free to secure the carriage.
Screwdriver
011306
2
011307
After replacing brushes, install the battery cartridge and break in the holders. 2. Release ...repaired by running and electric brake operation when releasing the switch trigger. Bevel angle
(1) 0° bevel angle Push the carriage toward the guide fence and tighten two clamp screws to slip in brushes by a Makita service...
XSL01Z Instruction Manual - Page 21
... made or attempted by Makita Authorized or Factory Service Centers, always using Makita replacement parts. They may result in this one of an accessory or attachment may be free of defects from workmanship and materials for its stated purpose. The use of any trouble develop during this manual. MAKITA LIMITED ONE YEAR WARRANTY
Warranty Policy...
XSL01Z Parts Breakdown - Page 3
Model XSL01Z Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part# Description
Q'ty Unit
001
188961-5
001 D10
002
417113-4
003
911268-2
...265717-4
045
266026-4
046
142720-1
046 C10 263002-9
046 C20 263005-3
046 C30 804C98-5
048
211021-9
HANDLE SET INC. 21 SWITCH BUTTON PAN HEAD SCREW M5X45 TAPPING SCREW 4X18 COMPRESSION SPRING 4 LOCK OFF LEVER PIN 5 TERMINAL...
XSL01Z Parts Breakdown - Page 4
... SPIRAL SPRING 26 SAFETY COVER FLAT WASHER 5 PAN HEAD SCREW M5X18 COMPRESSION SPRING 6 GUIDE FENCE H.S.H.BOLT M6X25 WITH WG SCREW M6X10 SLEEVE 17 TORSION SPRING 28 SLEEVE 17 THUMB SCREW M6X28 COMPRESSION SPRING 6 RING 26 PIPE HOLDER H.S.SET SCREW(CUP POINT)M6X8 STRAIN RELIEF TAPPING SCREW BIND CT 4X12 PAN HEAD SCREW...
XSL01Z Parts Breakdown - Page 5
...
266432-3
190
273658-0
191
286212-1
192
921472-5
193
251887-5
194
140611-0
194 C10 816339-9
194 C20 810483-4
FLAT WASHER 8 + PAN HEAD SCREW M6 H.S.SET SCREW(FLAT POINT)M6X10 H.S.SET SCREW(FLAT POINT)M6X10 KNOB 20 O RING 5 STOPPER PIN PIN 16-90 ARM HOLDER COMPLETE BEVEL SCALE LABEL PIN 5 SCREW M10 FLAT WASHER...
Makita XSL01Z Reviews
We have not received any reviews for Makita yet.