Makita DT04R1 Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita DT04R1 manuals!
Problems with Makita DT04R1?
Ask a Question
Free Makita DT04R1 manuals!
Problems with Makita DT04R1?
Ask a Question
Popular Makita DT04R1 Manual Pages
DT04 Instruction Manual - Page 2
... interrupter (GFCI) protected supply. Use personal protective equipment. ENGLISH (Original instructions)
SPECIFICATIONS
Model: Fastening capacities
No load speed (RPM) Impacts per minute
Machine screw ... development, the specifications herein are subject to change without notice.
• Specifications and battery cartridge may differ from heat, oil, sharp edges or moving parts. Failure to...
DT04 Instruction Manual - Page 3
... off. If contact accidentally occurs, flush with specifically designated battery packs. Hold power tool by a qualified
repair person using the tool in this instruction manual may affect the power tool's operation. Hold the tool firmly. 4. MISUSE or failure to safety rules for operations different from moving parts, breakage of children and do the job better...
DT04 Instruction Manual - Page 4
... e.g. SAVE THESE INSTRUCTIONS.
Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life.
3.
FUNCTIONAL... Makita warranty for hazardous material is equipped with a little click.
Do not use genuine Makita batteries...CAUTION: Only use a damaged battery.
10. CAUTION: Always install the battery cartridge fully until it locks in a fire.
...
DT04 Instruction Manual - Page 5
.... NOTE: The tool automatically stops if you turn the tool on the conditions of the model number
1
2
► 1 .
Indicator lamps 2.
Indicator lamps
Remaining capacity
Switch action
1
► 1 . Electric brake
This tool is equipped with "B" at a Makita service center. Indicating the remaining battery capacity
Only for battery cartridges with an electric brake. Low...
DT04 Instruction Manual - Page 6
... the button is in the neutral position, the switch trigger cannot be pulled.
4 1
You can be changed.
5 3
► 1 .
CAUTION: When not operating the tool, always set the reversing switch lever to a complete stop. For approximately one second within 10 seconds.
"A mode (assist mode)" is overheated, the light flashes for one minute...
DT04 Instruction Manual - Page 7
... available only when the tool rotates clockwise. Sleeve
To install the driver bit, pull the sleeve in the figure. NOTE: If the driver bit is not inserted deep enough into the sleeve as...force grade can be secured. Then release the sleeve to the instructions above. Soft
1,600 min-1 (/min)
Tightening with better control. To remove the driver bit, pull the sleeve in A mode, the impact force ...
DT04 Instruction Manual - Page 8
... to each bolt diameter
Hold the tool firmly and place the point of the driver bit in the screw head. Fastening time (second) 2.
This can be fastened...(29)
20 (14)
M12(1/2")
M12(1/2") M10(3/8")
M8(5/16")
3
M10(3/8")
M8(5/16")
0
1.0
2.0
3.0
1
1. Installing hook
1 2 3
► 1 . Proper fastening torque corresponding to continue the operation, rest the tool at least 15...
DT04 Instruction Manual - Page 9
... Factory Service Centers, always using the holster, remove a driver bit/drill bit from the tool. Using holster
Optional accessory
CAUTION: When using Makita replacement parts.
9 ENGLISH
NOTICE: Never use the correct size driver bit or socket bit will cause a reduction in the holster and lock it holds the tool firmly.
1. To maintain product SAFETY and RELIABILITY, repairs...
DT04 Instruction Manual - Page 10
... during this manual. If inspection shows the trouble is warranted to persons.
Only use of injury to be included in the list may be free of defects from workmanship and materials for its stated purpose. It is caused by others: • repairs are recommended for use with your local Makita Service Center. • Driver bits •...
DT04 Parts Breakdown - Page 2
...9 PC. 1 PC. 1 PC. 1 1 1 1 1 PC. 1 PC. 1 PC. 1 1 PC. 1 1 1 2 PC. 1 1 PC. 24 PC. 1 PC. 1 1 PC. 2 PC. 2 1 PC. 2 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 2 PC. 0 1 3 PC. 1 0 1 PC. 1 1 PC. 1 (DT04R1) 1 (DT04R1) 0 2 (DT04R1) 1 (DT04R1) 2 PC. (DT04R1) 1 Model DT04 R1/Z Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part#
Description
Q'ty Unit
001
183E65-8 HOUSING SET
001 C10 252126-6 HEX.
Makita DT04R1 New Tool Flyers English - Page 1
...Bare Tool Model DT04Z
SPECIFICATIONS
Hex Shank No Load Speed (var. 2 spd) Impacts Per Minute (var. 2 spd.) Maximum Torque (in.lbs./N•m) Battery Overall Length Net Weight (with battery) UPC Code DT04R1 UPC Code DT04Z
1/4" ...Motor delivers 1,200 in .lbs. 12V max CXT™ Lithium-Ion Brushless Cordless Impact Driver Kit (2.0Ah)
Model DT04R1
Compact, Brushless and Ergonomic Design
5-5/...
Makita DT04R1 Reviews
We have not received any reviews for Makita yet.