Makita XNB01 Instruction Manual
Page 2
... such as in the off-position before turning the power tool on invites accidents. 13. Do not use a power tool while you are doing and use a ground fault circuit interrupter (GFCI) protected supply. Prevent unintentional starting. Do not overreach. Electrical Safety 4. Never use . If operating a power tool in electric shock, fire and/or serious injury. ENGLISH (Original instructions) SPECIFICATIONS Model XNB01 Brad nail size 18Ga x 15, 20, 25, 30, 32...
... such as in the off-position before turning the power tool on invites accidents. 13. Do not use a power tool while you are doing and use a ground fault circuit interrupter (GFCI) protected supply. Prevent unintentional starting. Do not overreach. Electrical Safety 4. Never use . If operating a power tool in electric shock, fire and/or serious injury. ENGLISH (Original instructions) SPECIFICATIONS Model XNB01 Brad nail size 18Ga x 15, 20, 25, 30, 32...
Makita XNB01 Instruction Manual
Page 3
... the power tool is placed firmly against the workpiece. Maintain power tools. Do not force the power tool. Do not use the power tool if the switch does not turn it was designed. 18. Always assume that the safety of dust extraction and collection facilities, ensure these are easier to operate the power tool. Do not use this nailer for fastening electrical cables. Use the power tool, accessories and tool bits etc. Use of starting the power tool accidentally...
... the power tool is placed firmly against the workpiece. Maintain power tools. Do not force the power tool. Do not use the power tool if the switch does not turn it was designed. 18. Always assume that the safety of dust extraction and collection facilities, ensure these are easier to operate the power tool. Do not use this nailer for fastening electrical cables. Use the power tool, accessories and tool bits etc. Use of starting the power tool accidentally...
Makita XNB01 Instruction Manual
Page 4
... the safety lever. Use only fasteners specified in this instruction manual may result in use of any other fasteners may allow the fastener to avoid accidental firing. ・ volts ・ direct current IMPORTANT SAFETY INSTRUCTIONS ENC007-8 FOR BATTERY CARTRIDGE 1. Do not operate the tool without fasteners. Stop driving operations immediately if you are prepared to safety rules for the subject product. Check the safety lever frequently for lubricating and changing accessories...
... the safety lever. Use only fasteners specified in this instruction manual may result in use of any other fasteners may allow the fastener to avoid accidental firing. ・ volts ・ direct current IMPORTANT SAFETY INSTRUCTIONS ENC007-8 FOR BATTERY CARTRIDGE 1. Do not operate the tool without fasteners. Stop driving operations immediately if you are prepared to safety rules for the subject product. Check the safety lever frequently for lubricating and changing accessories...
Makita XNB01 Instruction Manual
Page 5
.... CAUTION: • Always install the battery cartridge fully until it is equipped with a little click. Battery cartridge 3 014581 CAUTION: • Always switch off power to the motor to you or someone around you notice less tool power. 2. Do not use it may reach or exceed 50 ゚ C (122 ゚ F). 7. Tips for a long period of the button, it locks in the housing...
.... CAUTION: • Always install the battery cartridge fully until it is equipped with a little click. Battery cartridge 3 014581 CAUTION: • Always switch off power to the motor to you or someone around you notice less tool power. 2. Do not use it may reach or exceed 50 ゚ C (122 ゚ F). 7. Tips for a long period of the button, it locks in the housing...
Makita XNB01 Instruction Manual
Page 6
... not in use , always set the lock button in the "LOCK" position and remove the battery cartridge from the tool. Before nailing, set it in the " FREE" position. Continuous mode 3 014618 The tool has two different nailing modes. For more detail, see the section "OPERATION". Intermittent nailing (sequential mode) This mode suits for tool When the tool is set the lock button in the "LOCK" position. A BB 1. Do not turn the adjuster to B direction.
... not in use , always set the lock button in the "LOCK" position and remove the battery cartridge from the tool. Before nailing, set it in the " FREE" position. Continuous mode 3 014618 The tool has two different nailing modes. For more detail, see the section "OPERATION". Intermittent nailing (sequential mode) This mode suits for tool When the tool is set the lock button in the "LOCK" position. A BB 1. Do not turn the adjuster to B direction.
Makita XNB01 Instruction Manual
Page 7
... personal injuries. • Load nails in this case, charge the battery cartridge. Return the slide door to scratch the lens of light directly. 3 2 1. To remove the nails, press the lock lever and slide the slide door. Center plate 3 4. When not in use, store the nose adapter in wrong direction may cause nail jamming and breakage of the nailer. 1. The lamp goes out 10 seconds after releasing the trigger or contact element...
... personal injuries. • Load nails in this case, charge the battery cartridge. Return the slide door to scratch the lens of light directly. 3 2 1. To remove the nails, press the lock lever and slide the slide door. Center plate 3 4. When not in use, store the nose adapter in wrong direction may cause nail jamming and breakage of the nailer. 1. The lamp goes out 10 seconds after releasing the trigger or contact element...
Makita XNB01 Instruction Manual
Page 8
... for repairs. • Before installing the battery cartridge into a groove in the figure to the "FREE" position. Place the 2 contact element against the workpiece and pull the trigger. Hex wrench 1 014589 When not in use, store the hex wrench as mentioned in working order before each operation. Pull the trigger 1 2. Continuous/ intermittent nailing (continuous mode) 1. To drive a nail, set the lock button to keep it out. Screw 1 3 2 014588...
... for repairs. • Before installing the battery cartridge into a groove in the figure to the "FREE" position. Place the 2 contact element against the workpiece and pull the trigger. Hex wrench 1 014589 When not in use, store the hex wrench as mentioned in working order before each operation. Pull the trigger 1 2. Continuous/ intermittent nailing (continuous mode) 1. To drive a nail, set the lock button to keep it out. Screw 1 3 2 014588...
Makita XNB01 Instruction Manual
Page 9
... next actuation, you do not need to direct sunlight. Nails Nail NOTE: • This tool stops automatically under the following conditions: − If you need to restart the operation. Anti dry fire mechanism This tool is released, and the battery cartridge and nails are removed before removing jammed nails. 1. It automatically stops driving nails when the remaining nails finish. Hex bolt B 3. Secure the driver guide cover with hex bolts in a very...
... next actuation, you do not need to direct sunlight. Nails Nail NOTE: • This tool stops automatically under the following conditions: − If you need to restart the operation. Anti dry fire mechanism This tool is released, and the battery cartridge and nails are removed before removing jammed nails. 1. It automatically stops driving nails when the remaining nails finish. Hex bolt B 3. Secure the driver guide cover with hex bolts in a very...
Makita XNB01 Instruction Manual
Page 10
... other parts to be free of defects from workmanship and materials for its stated purpose. Spring (small) 5. To maintain product SAFETY and RELIABILITY, repairs, any trouble develop during this manual. IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM THE SALE OR USE OF THE PRODUCT. This Warranty gives you specific legal rights, and you install...
... other parts to be free of defects from workmanship and materials for its stated purpose. Spring (small) 5. To maintain product SAFETY and RELIABILITY, repairs, any trouble develop during this manual. IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM THE SALE OR USE OF THE PRODUCT. This Warranty gives you specific legal rights, and you install...
Makita XNB01Z Parts Breakdown
Page 2
...-7 ADJUSTER GUIDE 029 326399-8 ADJUSTER ROD 030 262130-7 URETHANE RING 4 031 266026-4 TAPPING SCREW BIND CT 4X12 032 454938-5 SWITCH BASE 033 632C01-4 SWITCH UNIT 034 454939-3 TRIGGER 035 632C01-4 SWITCH UNIT 036 234037-7 COMPRESSION SPRING 5 037 454952-1 TRIGGER LOCK 038 CB440 CARBON BRUSH CB-440 (195021-6) 039 632B92-9 BRUSH HOLDER COMPLETE 040 643860-3 TERMINAL 041 619339-6 ARMATURE 042 638989-8 YOKE UNIT 043 187809-8 MOTOR HOUSING SET 043...
...-7 ADJUSTER GUIDE 029 326399-8 ADJUSTER ROD 030 262130-7 URETHANE RING 4 031 266026-4 TAPPING SCREW BIND CT 4X12 032 454938-5 SWITCH BASE 033 632C01-4 SWITCH UNIT 034 454939-3 TRIGGER 035 632C01-4 SWITCH UNIT 036 234037-7 COMPRESSION SPRING 5 037 454952-1 TRIGGER LOCK 038 CB440 CARBON BRUSH CB-440 (195021-6) 039 632B92-9 BRUSH HOLDER COMPLETE 040 643860-3 TERMINAL 041 619339-6 ARMATURE 042 638989-8 YOKE UNIT 043 187809-8 MOTOR HOUSING SET 043...
Makita XNB01Z Parts Breakdown
Page 3
... CYLINDER END CUSHION HEX. SOCKET HEAD BOLT M4X16 O RING 14 COMPRESSION SPRING 4 O RING 3 O RING 3 VALVE STEM COMPRESSION SPRING 6 SLEEVE COMPRESSION SPRING 3 STOPPER PUSHER SLIDE DOOR PIN 3 LOCK LEVER COMPRESSION SPRING 7 URETHANE RING 3 NAIL PLATE MAGAZINE COMPLETE HEX. SOCKET HEAD BOLT M4X12 GEAR ASSEMBLY RETAINING RING S-12 BALL BEARING 6001ZZ EDGE CAM WOODRUFF KEY 3 BALL BEARING 6002ZZ CRANK MAGNET BASE COMPLETE PAN HEAD SCREW M4X8 CRANK CASE HEX. 045 266130-9 046 651533...
... CYLINDER END CUSHION HEX. SOCKET HEAD BOLT M4X16 O RING 14 COMPRESSION SPRING 4 O RING 3 O RING 3 VALVE STEM COMPRESSION SPRING 6 SLEEVE COMPRESSION SPRING 3 STOPPER PUSHER SLIDE DOOR PIN 3 LOCK LEVER COMPRESSION SPRING 7 URETHANE RING 3 NAIL PLATE MAGAZINE COMPLETE HEX. SOCKET HEAD BOLT M4X12 GEAR ASSEMBLY RETAINING RING S-12 BALL BEARING 6001ZZ EDGE CAM WOODRUFF KEY 3 BALL BEARING 6002ZZ CRANK MAGNET BASE COMPLETE PAN HEAD SCREW M4X8 CRANK CASE HEX. 045 266130-9 046 651533...
Makita XNB01Z Parts Breakdown
Page 4
... A04 424121-8 NOSE ADAPTER A05 783201-2 HEX. SOCKET HEAD BOLT M4X6 111 266369-4 HEX SOCKET HEAD BOLT M5X20 112 266130-9 TAPPING SCREW BIND PT 3X16 113 815P32-8 XNB01 NAME PLATE 114 911118-1 PAN HEAD SCREW M4X12 115 187862-4 HOUSING SET 115 C10 252126-6 HEX. SOCKET HEAD BOLT M4X6 107 310586-9 DRIVER GUIDE 108 922102-1 HEX. WRENCH 3 D01 654510-5 INSULATED CONNECTOR 5.5-SD 1 1 2 PC. 1 1 1 1 PC...
... A04 424121-8 NOSE ADAPTER A05 783201-2 HEX. SOCKET HEAD BOLT M4X6 111 266369-4 HEX SOCKET HEAD BOLT M5X20 112 266130-9 TAPPING SCREW BIND PT 3X16 113 815P32-8 XNB01 NAME PLATE 114 911118-1 PAN HEAD SCREW M4X12 115 187862-4 HOUSING SET 115 C10 252126-6 HEX. SOCKET HEAD BOLT M4X6 107 310586-9 DRIVER GUIDE 108 922102-1 HEX. WRENCH 3 D01 654510-5 INSULATED CONNECTOR 5.5-SD 1 1 2 PC. 1 1 1 1 PC...
Makita XNB01Z New Tool Flyer English
Page 1
... Lithium-Ion Rapid Optimum 4-Port Charger (DC18SF) All specifications subject to stock on a single charge using BL1830 battery (batterynot included) VERSATILITY Drives a range of accessories. Patent and Trademark Office Makita offers a wide variety of 18 gauge brad nailsfrom5/8" to2"; 18V LXT® Lithium-Ion Cordless 2" Brad Nailer, 18 Ga., Tool Only Model XNB01Z Contact or Sequential Nailing RUN TIME Drives 1,000 nails on hand. makitatools.com Makita...
... Lithium-Ion Rapid Optimum 4-Port Charger (DC18SF) All specifications subject to stock on a single charge using BL1830 battery (batterynot included) VERSATILITY Drives a range of accessories. Patent and Trademark Office Makita offers a wide variety of 18 gauge brad nailsfrom5/8" to2"; 18V LXT® Lithium-Ion Cordless 2" Brad Nailer, 18 Ga., Tool Only Model XNB01Z Contact or Sequential Nailing RUN TIME Drives 1,000 nails on hand. makitatools.com Makita...