Makita LXDG01Z Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita LXDG01Z manuals!
Problems with Makita LXDG01Z?
Ask a Question
Free Makita LXDG01Z manuals!
Problems with Makita LXDG01Z?
Ask a Question
Popular Makita LXDG01Z Manual Pages
Owners Manual - Page 2
... tool or battery-operated (cordless) power tool. Do not overreach. Cluttered or
dark areas invite accidents. 2. If operating a power tool in the warnings refers to EPTA-Procedure 01/2003
GEA006-2
General Power Tool Safety Warnings
WARNING Read all safety warnings and all times. Always wear eye protection. ENGLISH (Original instructions)
SPECIFICATIONS
Model
LXDG01
Max...
Owners Manual - Page 3
... the power tool repaired before making any other accessory must be caught in accordance with the power tool or these instructions, taking into account the working conditions and the work to follow all safety warnings, instructions, illustrations and specifications provided with specifically designated battery packs. Keep cutting tools sharp and clean. in moving parts, breakage of...
Owners Manual - Page 4
...saw blade. b) Wheels must be used only for which in electrocution or shock. 16. As appropriate, wear dust mask, hearing protectors, gloves and workshop apron capable of the power tool "live" and shock the operator. 11. Regularly clean the power tool's air vents. Kickback is not suitable for damage or install...of operation. 10. Safety Warnings Specific for Grinding: a) Use only wheel...
Owners Manual - Page 5
... supported. 27. Handle and store wheels with clear water and seek medical attention right away. Do not disassemble battery cartridge. 3. Do not store the tool and battery cartridge in a fire. 8. Watch out for tool. ･ volts
･ direct current
･ rated speed
･ revolutions or reciprocation per minute
IMPORTANT SAFETY INSTRUCTIONS
ENC007-6
FOR BATTERY...
Owners Manual - Page 6
... charging it may accidentally fall out of the cartridge.
• To install the battery cartridge, align the tongue on the tool. Overcharging shortens the battery service life. 3. Apply caution when locking tool in "ON" position for approximately one second. To start the tool again, move the slide switch to the "O (OFF)" position once and then to the...
Owners Manual - Page 7
... "I (ON)" position, the tool does not start the tool, first slide the slide switch toward the "I (ON)" position. Keep the carbon brushes clean and free to install a 1/8" shank wheel point.
001145
Remove and check the carbon brushes regularly. Collet nut 4. Wheel point 3. − Battery cartridge replacing signal − When the remaining battery capacity gets low, the...
Owners Manual - Page 8
... set • Various type of Makita genuine batteries and
chargers
CAUTION: • These accessories or attachments are
recommended for use of slotted bit screwdriver into the notch in the tool and remove the holder cap cover by Makita Authorized or Factory Service Centers, always using the tool without handle, always install
the rubber protector on the tool. • When installing...
Owners Manual - Page 9
... "FITNESS FOR A SPECIFIC PURPOSE," AFTER THE ONE YEAR TERM OF THIS WARRANTY. THIS DISCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY.
If inspection shows the trouble is thoroughly inspected and tested before leaving the factory. MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is caused by others: repairs are required because...
Parts Breakdown - Page 2
...195018-5 643929-3 419518-4 326009-7 210042-8 213445-5 961005-4 317821-6 781039-9 450128-8 DC18RA BL1830 892170-7
Part Name INSULATION COVER COLLET NUT COLLET CONE 1/4' BEARING RETAINER FELT RING 17 FLAT WASHER 18 SPINDLE BALL ... UNIT ENDBELL COMPLETE LXDG01 NAME PLATE TAPPING SCREW 4X18 SWITCH KNOB HOUSING SET INC. 29 SWITCH LEVER SWITCH 1246.3223 CONTROLLER TERMINAL HOUSING SET INC. 24 CARBON...
Flyer (English) - Page 1
...8226; L.E.D.Light Flashes Red when it is Time to Recharge the Battery
Makita-built motor delivers 25,000 RPM for Operator Convenience • Vent... Protection Circuit with over-torque control protects the motor
PERFORMANCE
Models LXDG01 LXDG01Z
18V LXT Li-Ion batteries charge in L.E.D. 18V LXT® LITHIUM-ION CORDLESS 1/4" DIE GRINDER
SPEED
COMPACT BARREL GRIP DESIGN WITH 25,000 ...
Flyer (English) - Page 2
18V LXT® LI-ION CORDLESS 1/4" DIE GRINDER
Models LXDG01 / LXDG01Z
FEATURES & BENEFITS
n Makita-built motor delivers 25,000 RPM for LXDG01Z
SPECIFICATIONS
Collet
No load speed
Max wheel diameter
Battery
Overall length
Net weight
Shipping weight: LXDG01 LXDG01Z
Master carton qty: LXDG01 LXDG01Z
UPC code:
LXDG01 LXDG01Z
1/4" 25,000 RPM
1-1/2" 18V LXT Lithium-Ion
15...
Makita LXDG01Z Reviews
We have not received any reviews for Makita yet.