Makita LS1040F Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita LS1040F manuals!
Problems with Makita LS1040F?
Ask a Question
Free Makita LS1040F manuals!
Problems with Makita LS1040F?
Ask a Question
Popular Makita LS1040F Manual Pages
Owners Manual - Page 1
www.makitatools.com SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. Compound Miter Saw
Equipped with Electric Blade Brake 255 mm (10") MODEL LS1040
DOUBLE INSULATION
INSTRUCTION MANUAL
WARNING: For your personal safety, READ and UNDERSTAND before using.
Owners Manual - Page 3
... is dusty. The use only identical replacement parts.
23. Follow instructions for alignment of moving parts, binding of moving parts. Don't leave tool until it frees both hands to contain long hair.
11. Keep proper footing and balance at the rate for which it was not designed.
10. When servicing use of improper accessories may get caught...
Owners Manual - Page 4
... overheating. Using a power source with product (gained from repeated use one heavy enough to miter saw blade. The smaller the gage number, the heavier the cord. as well as that specified for proper closing before changing blade or servicing.
8. Unplug tool before each use depending on the nameplate of cord in doubt, DO...
Owners Manual - Page 5
...manual...be toxic. Use of security. 9. Replace cracked or damaged blade immediately. Watch ... of flammable liquids or gases.
10. NEVER hold workpiece on an actual...installing surface) or bolt. Always use the tool in the base to fasten the saw and increases potential for a while. Do not abuse cord. Never yank cord to these parts could indicate poor installation...
Owners Manual - Page 8
... be sure that the blade is no longer easily visible, unplug the saw and clean the guard carefully with a damp cloth. Check to loosen the hex bolt holding blade guard. If the see-through age or UV light exposure, contact a Makita service center for a new guard.
Do not remove spring holding the center...
Owners Manual - Page 13
...• When cutting long workpieces, use of the turn base. Sub-fence
13 Support 2. NOTE: If you connect a Makita vacuum cleaner to always secure the workpiece properly and tightly with the sub-fence.... Securing workpiece
WARNING:
• It is extremely important to your saw, more ...
Owners Manual - Page 16
...THE BLADE HAS COME TO A COMPLETE STOP before returning the blade to its fully elevated position.
2. Miter cutting Refer to bevel
direction during a bevel cut the workpiece. Secure the workpiece with the vise. ... the cut is applied, the blade will vibrate and leave a mark (saw mark) in overload of saw blade to set the bevel angle (Refer to secure the selected bevel angle safely. Keep...
Owners Manual - Page 17
...crown moldings and one type of the blade. Compound cutting Compound cutting is the process in which a bevel ...Miter angle Left and Right 0 - 45˚
When performing compound cutting, refer to the left position when performing left bevel cuts.
4. Compound cutting can be impaired.
• Always set the sub-fence to "Press cutting", "Miter cutting" and "Bevel cut on a compound miter saw...
Owners Manual - Page 18
... to check the saw base as wall length. A: • Tilt and secure bevel angle setting to 33.9°
LEFT.
• Adjust and secure miter angle setting to 31.6° RIGHT.
• Lay crown molding with its broad back (hidden) surface down on the turn base with its CEILING CONTACT EDGE against the guide fence on...
Owners Manual - Page 19
...˚
000031 Compound Miter Saw Miter and Bevel Angle Settings
EN0002-1
Wall
Wall to Crown Molding Angle: 52/38 degrees
Wall Angle Bevel Angle Miter Angle
(deg...14.5
11.6
144 14.1
11.3
145 13.7
11.0
146 13.3
10.7
147 12.9
10.3
148 12.5
10.0
149 12.2
9.7
150 11.8
9.4
151 11.4
9.0
152 11.0
8.7
153 10.8
8.4
154 10.2
8.1
155 9.8
7.8
156 9.4
7.5
157 9.0
7.1
158 8.6
...
Owners Manual - Page 20
...000032 Compound Miter Saw Miter and Bevel Angle Settings
EN0003-1
Wall
Wall to Crown Molding Angle: 45 degrees
Wall Angle Bevel Angle Miter Angle Wall Angle Bevel Angle Miter Angle...12.9
145 12.3
12.6
146 11.9
12.2
147 11.6
11.8
148 11.2
11.5
149 10.9
11.1
150 10.5
10.7
151 10.2
10.4
152 9.8
10.0
153 9.5
9.6
154 9.2
9.3
155 8.8
8.9
156 8.5
8.5
157 8.1
8.2
158 7.8
7.8...
Owners Manual - Page 22
... pieces of stock to the same length, ranging from moving, move the set plate (optional accessory) will be installed so that the screw heads are below the surface of the holder-rod ...assembly (optional accessory) allows cutting repetitive lengths up to the guide fence. Align the cutting ...
Owners Manual - Page 26
... bag • Crown molding stopper set • Triangular rule • Lock-off button (2 pcs.)
26 Slices cleanly against the grain. The use accessory or attachment for
use with your local Makita service center.
• Steel & Carbide-tipped saw blades
Miter saw blades
Combination
Crosscutting
Fine cross cuts Non-ferrous metals miter saw blades
For smooth and precise cutting...
Owners Manual - Page 31
... to the outside of the Makita Factory Service Centers listed, or to one of the carton detailing the problem with your tool. FACTORY SERVICE CENTERS
1-800-4-MAKITA
RETAIN THIS PORTION FOR YOUR ... 541-4776
CUSTOMER'S RECORD
When you need service: Send complete tool (prepaid) to an Authorized Makita Service Center. Date Purchased Dealer's Name & Address
Model No. La Mirada, CA 90638-5753 (...
Parts Breakdown - Page 3
..., LS1011 T. BOLT M8X75, LS1030 RUBBER SLEEVE 6, LS1030 TAPPING SCREW 4X18, 4323K GUIDE COVER, LS1040 HELICAL GEAR 42, LS1040 HOUSING W/O BEARING, LS1040 B. Parts Breakdown
LS1040F
Products with multiple versions are listed in subsiding order with the newest version on top not indented
Fig # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 20 21 22 23 24...
Makita LS1040F Reviews
We have not received any reviews for Makita yet.