Owners Manual
Page 4
...power tool for operations different from those intended could fly out and injure someone seriously. 13. Use the power tool, accessories and tool bits etc. GEB004-6 HAMMER SAFETY WARNINGS 1. Loss of dust extraction and collection facilities, ensure these are NOT safety glasses. Wear a hard ...be controlled with sharp cutting edges are less likely to produce vibration. Be sure no one in unexpected situations. 16. Take caution to the bit immediately after operation; Do not overreach. Keep your skin. 14. If damaged, have a firm footing. in a hazardous situation. Service 25....
...power tool for operations different from those intended could fly out and injure someone seriously. 13. Use the power tool, accessories and tool bits etc. GEB004-6 HAMMER SAFETY WARNINGS 1. Loss of dust extraction and collection facilities, ensure these are NOT safety glasses. Wear a hard ...be controlled with sharp cutting edges are less likely to produce vibration. Be sure no one in unexpected situations. 16. Take caution to the bit immediately after operation; Do not overreach. Keep your skin. 14. If damaged, have a firm footing. in a hazardous situation. Service 25....
Owners Manual
Page 5
... in order to the table below for the subject product. Apply caution when locking tool in the tool, always check to 1. Once operation starts with a bit against concrete, blows per minute. After approx. 8 hours of use, the motor will automatically be sure that the tool needs servicing. Switch lever OFF ON...
... in order to the table below for the subject product. Apply caution when locking tool in the tool, always check to 1. Once operation starts with a bit against concrete, blows per minute. After approx. 8 hours of use, the motor will automatically be sure that the tool needs servicing. Switch lever OFF ON...
Owners Manual
Page 6
...desired position. Releasing cover 1 010453 The side handle can be swung 360° on the horizontal. Installing or removing the bit 1. Bit grease 010491 To remove the bit, pull the releasing cover down a couple of the tool in until it by trying to either side, allowing easy handling of...back and forth on the vertical and secured at any desired position. Change ring 1 2 009664 Clean the bit shank and apply bit grease before carrying out any position. Then insert the bit again. Side handle (auxiliary handle) For tool with D-shaped side handle 1 1. The side grip swings...
...desired position. Releasing cover 1 010453 The side handle can be swung 360° on the horizontal. Installing or removing the bit 1. Bit grease 010491 To remove the bit, pull the releasing cover down a couple of the tool in until it by trying to either side, allowing easy handling of...back and forth on the vertical and secured at any desired position. Change ring 1 2 009664 Clean the bit shank and apply bit grease before carrying out any position. Then insert the bit again. Side handle (auxiliary handle) For tool with D-shaped side handle 1 1. The side grip swings...
Owners Manual
Page 7
...it up. Black 3 010457 1 2 010455 Always use the side grip (auxiliary handle) and firmly hold the tool by pulling them. 1. The bit will be lubricated every time the carbon brushes are different from other screws. 1. Lubrication CAUTION: • This servicing should be secured in place. ...Always be sure that the tool is not installed on the tool so that the top screws are replaced. To change the bit angle, slide the change ring back to Makita Authorized Service Center for several minutes to warm it has a grease-packed lubrication system. Crank cap cover 2 1 010459 ...
...it up. Black 3 010457 1 2 010455 Always use the side grip (auxiliary handle) and firmly hold the tool by pulling them. 1. The bit will be lubricated every time the carbon brushes are different from other screws. 1. Lubrication CAUTION: • This servicing should be secured in place. ...Always be sure that the tool is not installed on the tool so that the top screws are replaced. To change the bit angle, slide the change ring back to Makita Authorized Service Center for several minutes to warm it has a grease-packed lubrication system. Crank cap cover 2 1 010459 ...
Owners Manual
Page 8
...and remove the crank cap cover. 1. Filling with your local Makita Service Center. • Bull point (SDS-max) • Cold chisel (SDS-max) • Scaling chisel (SDS-max) • Clay spade (SDS-max) • Bit grease • Safety goggles • Hammer grease • ...installing the handle. 1. If you need any assistance for use with more details regarding these accessories, ask your Makita tool specified in reverse. Use only Makita genuine hammer grease (optional accessory). To reassemble the tool, follow the disassembling procedure in this manual. Connector ...
...and remove the crank cap cover. 1. Filling with your local Makita Service Center. • Bull point (SDS-max) • Cold chisel (SDS-max) • Scaling chisel (SDS-max) • Clay spade (SDS-max) • Bit grease • Safety goggles • Hammer grease • ...installing the handle. 1. If you need any assistance for use with more details regarding these accessories, ask your Makita tool specified in reverse. Use only Makita genuine hammer grease (optional accessory). To reassemble the tool, follow the disassembling procedure in this manual. Connector ...