Makita HM0870C Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita HM0870C manuals!
Problems with Makita HM0870C?
Ask a Question
Free Makita HM0870C manuals!
Problems with Makita HM0870C?
Ask a Question
Makita HM0870C Videos
Makita HM0870C
Duration: 1:16
Total Views: 11,816
Duration: 1:16
Total Views: 11,816
Makita HM0870C 110V SDS-Max Demolition Hammer DEMO
Duration: 2:01
Total Views: 193
Duration: 2:01
Total Views: 193
Popular Makita HM0870C Manual Pages
Owners Manual - Page 1
ENGLISH (Original instructions)
INSTRUCTION MANUAL
Demolition Hammer
HM0871C HM0870C
DOUBLE INSULATION
010450
WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FU1 TURE REFERENCE.
Owners Manual - Page 2
...Uncertainty (K) : 1.5 m/s2
ENG306-1
Work mode : chiseling function with appropriate accessories. ENE045-1
Intended use .
･ Read instruction manual.
･ DOUBLE INSULATION
･ Only for EU ... of European Directive 2002/96/EC on single-phase AC supply.
ENGLISH
SPECIFICATIONS
Model Blows per minute
HM0871C
HM0870C
1,100 - 2,650 min-1
Overall length
466 mm
449 mm
Net ...
Owners Manual - Page 3
... Makita machine(s): Designation of Machine: Demolition Hammer
Model No./ Type: HM0871C, HM0870C ...instructions for appropriate conditions will reduce personal injuries. 13. Protective equipment such as pipes, radiators, ranges and refrigerators. Carrying power tools with your mains-operated (corded) power tool or battery-operated (cordless..., sharp edges or moving parts. If operating a power ...
Owners Manual - Page 4
...bits etc. Keep handles dry, clean and free from moving parts. 11. GEB004-6
HAMMER SAFETY WARNINGS
1. Wear a hard hat (safety helmet), safety glasses and/or face shield. This will ensure that cannot be controlled with the power tool or these instructions... Always be repaired. 20. The bit could give the...using only identical replacement parts. If devices are...power tool serviced by ...
Owners Manual - Page 5
... brushes are nearly worn out to indicate that the tool needs servicing....Model HM0871C only
NOTE: • Blows at no longer work. Indicator lamp
1. The indicator lamp is lit but this does not show trouble... the tool may not have this instruction manual may be done even while the ... bit against concrete, blows per minute. This can be malfunction.
Switch action
1. The red service ...
Owners Manual - Page 6
... eight different positions back and forth on the vertical and secured at any desired position. Installing or removing the bit
1. Change ring
1
2
009664
Clean the bit shank and apply bit grease before carrying out any position.
Clamp nut
2
010490
After installing, always make sure that the tool is securely held in place by turning clockwise...
Owners Manual - Page 7
... so that the tool is not
installed on the tool will not bounce around, uncontrolled. At the desired angle, slide the change the bit angle. Connector 2. MAINTENANCE
010493
The bit can be lubricated every time the carbon brushes are different from other screws.
1. Note that the top screws are replaced.
NOTE: • The change ring...
Owners Manual - Page 8
... Bit grease • Safety goggles • Hammer grease • Plastic carrying case
1 2
010461
Connect the connector firmly and then reinstall the handle. CAUTION: • Do not tighten the crank cap excessively. Only use accessory or attachment for use of any other maintenance or adjustment should be performed by Makita Authorized Service Centers, always using Makita replacement parts...
Parts Breakdown - Page 2
...CYLINDER GUIDE
38
213611-4 O RING 46
39
233927-1 RING SPRING 34
40
267079-6 FLAT WASHER 34
41
451444-1 HOUSING COVER
42
922243-3 HEX. Model HM0870C Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part#... RING 38
19
213431-6 FLUORIDE RING 28
20
213394-6 O RING 23
21
324389-5 IMPACT BOLT
22
325732-1 RING 20
23
424245-0 RUBBER RING 20
24
318512-2 BARREL
25
...
Parts Breakdown - Page 3
... RING R-40 BALL BEARING 6203LLU WAVE WASHER 30 CRANK HOUSING COMPLETE TAPPING SCREW 5X25 FIX GUIDE CUSHION PLATE OIL SEAL 12 BALL BEARING 6201LLB FLAT WASHER 12 GRIP SPRING 70 SQUARE BOLT...115V MOTOR HOUSING CARBON BRUSH SET CB-350 195004-6 TAPPING SCREW 4X18 REAR COVER TAPPING SCREW 4X18 BRUSH HOLDER UNIT CONTROLLER LEAD UNIT LENS TAPPING SCREW 4X14 TAPPING SCREW 5X25 HM0870C NAME PLATE TAPPING ...
Parts Breakdown - Page 4
A03 C10 162271-8
A03 C20 450990-1
A03 C30 325809-2
A04
809667-9
LATCH HANDLE SHAFT HM0870C PLASTIC CASE LABEL
2 PC. 1 PC. 1 PC. 2 PC.
Makita HM0870C Reviews
We have not received any reviews for Makita yet.