Makita 9031 Support and Manuals
Popular Makita 9031 Manual Pages
Owners Manual - Page 1
Belt Sander
MODEL 9031
INSTRUCTION MANUAL
S PEClFICAT10 NS
Belt size
Belt speed
Overall length
30 mm x 533 mm (1.3116" x 21")
200 m - 1,000 m (656 ft. ~ 3,280 f t , ) / m ~ n .
380 mm (14-31/32")
* Manufacturer reserves the right t o change specifications without notice. * Note: Specifications may differ from country to country. WARNING: For your personal safety, READ and UNDERSTAND ...
Owners Manual - Page 2
...service facility. It's safer than using
your hand and it frees both hands t o operate tool.
11. DON'T OVERREACH. Keep tools sharp and clean for lubricating and changing accessories. Follow instructions...replace ... have repaired by cord...parts. STORE IDLE TOOLS. Keep proper footing and balance at the rate for example, don't use power tools in use, before servicing, and when changing accessories...
Owners Manual - Page 3
....
Don't use depending on and off.
20. REPLACEMENT PARTS. Check for use common sense. pipes, radiators, ranges, refrigerator enclosures.
21. Do not change the plug in this equipment has a polarized plug (one blade is damaged should be properly repaired or replaced by authorized service center. AVOID UNINTENTIONAL STARTING. When tool is damaged...
Owners Manual - Page 4
SAVE THESE INSTRUCTIONS.
4 Do not leave the tool running. VOLTAGE WARNING..., so do not use water on .
3.Keep hands away from rotating parts.
4.
as well as that specified for the tool can result in doubt, DO NOT PLUG ...IN THE TOOL. Make sure the belt is not contacting the workpiece before the switch is harmful t o the motor. ADDITIONAL ...
Owners Manual - Page 5
... side grip can slip the other end of the belt and that the tool is switched off and unplugged before installing or removing the belt. Loop the belt over the rear pulley.
See the figure a t right. Install it by screwing it firmly on the inside of the belt over the front pulley. Hold the tool as...
Owners Manual - Page 6
...the
tool on or off, Otherwise a poor sanding finish, damage to the belt of loss of control of the tool may result.... 0 When working with the tool, be very careful to stop the tool from the locked position, pull the trigger fully, then release it repaired...contact of the tool and belt with any part of numbers 1 through 6. Gently apply the tool ...
Owners Manual - Page 8
... product SAFETY and RELIABILITY, repairs, nay other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
8 Both carbon brushes should be replaced a t the same time. Use only identical carbon brushes.
3
Limit mark
Use a screwdriver to the limit mark. Replacing carbon brushes Remove and check the carbon...
Owners Manual - Page 9
...100
742305-9
I
120
742334-2
I
150
9 The accessories or attachments should be used only in this manual.
ACCESSORIES
CAUTION : These accessories or attachments are recommended for use of any other accessories or attachments might present a risk of injury t o persons. The use with your Makita tool specified in the proper and intended manner.
0 Abrasive belt (10 per pkg)
Part No.
Owners Manual - Page 10
BELT SANDER
Model 9031
June-01 - ' 9 5 US
Note: The switch and other part configurations may differ from country to country.
10
Owners Manual - Page 11
...MODEL 9031...
1
Pulley 3 3 - 6 4
19
1
Abrasive Belt 30x533 AAlOO
20
1
Pulley h e r
21
1
Flaf Washer 5
22
1
Hex Socket Head Bolt ...Brush Brush Holder Cap Motor Housing Complete FIELD ASSEMBLY Tapping Screw Bind ET 4x60 Baffle Plate Ball Bearing 627LB Insulation Washer ARMATURE ASSEMBLY IWith Item 49 5 0 52 & 531 Fan 60 Ball Bearing 808DDW
- - Note The switch and other part Specifications...
Owners Manual - Page 12
... made or attempted by defective workmanship or material, Makita will repair (or at our option, replace) without charge. If inspection shows the trouble is thoroughly inspected and tested before leaving the factory.
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES O F "MERCHANTABILITY" AND "FITNESS FOR A SPECIFIC PURPOSE.'' AFTER THE ONE-YEAR TERM O F THIS...
Makita 9031 Reviews
Do you have an experience with the Makita 9031 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Makita yet.
Earn 750 points for your review!