LevelOne FCS-1041 Support and Manuals
Get Help and Manuals for this LevelOne item
View All Support Options Below
Free LevelOne FCS-1041 manuals!
Problems with LevelOne FCS-1041?
Ask a Question
Free LevelOne FCS-1041 manuals!
Problems with LevelOne FCS-1041?
Ask a Question
Popular LevelOne FCS-1041 Manual Pages
Manual - Page 3
...installed, then carefully read and follow the instructions in the ―Installation‖ chapter to avoid damages due to faulty assembly and installation.
Minimum System Requirement...designed for Viewer & Recorder Application
Support OS
XP, Windows 7
System Hardware...part of the warnings in ―Quick installation guide‖ before installing...camera but also can set up the Network ...
Manual - Page 5
...may damage the unit and result in an internal microphone. Antenna (Wireless model only)
4. Factory Default Reset This button is located on the head... the rear of Network Camera's. Network Camera User's Manual
Note: Using a power supply with a different voltage than... disconnection.
8.Microphone in and Audio out The Network Camera supports two way audio communication so that supply the power to...
Manual - Page 18
... seconds if the DDNS registration result is entered in the c2.mylevel1.com Password. In Network page-DDNS settings of the MAC. You can use the service ―C2.mylevel1.com‖. When you want and your router and camera manually if the registration is last six number of this camera. Then you can...
Manual - Page 32
...supports video only, audio only, and audio/video. PPPoE If using the PPPoE interface, you should fill the following settings from options： 1. Note: The maximum length of PPPoE account (3) "Confirm password": Input password... -
WIRELESS LAN (Wireless Model Only) "SSID" (Service Set Identifier), it is ―auto‖. The default setting is to a specific WLAN (Wireless Local Area ...
Manual - Page 34
... be displayed in the DDNS server. 6. "ASCII" is a code for logging in the Host name (xxxx. "Enable DDNS" This option turns on this button to use DDNS service, this field is registered in the DDNS Registration Result column and messaging E-mail. 3. Network Camera User's Manual
(6) "Key format" Choosing one of the following : 64...
Manual - Page 38
"Color mode" Select use color or monochrome video display. 2. Network Camera User's Manual
Audio and Video setting
General Setting
1. "Video orientation" The orientation of video
(1) "Flip" Vertically rotate the video.
38/62
Manual - Page 44
... codec setting (1) "Select Stream" The Network Camera supports "Stream... 1"and "Stream 2".
44/62 "AMR" The bit rates are selectable at the following rates: 4750,5150,5900,6700,7400,7950,10200 and 12200. -- "AAC" The bit rates are two choices of audio codec types available: "AMR"、 "AAC" and "G.711". (2) "Bit rate" -- Network Camera User's Manual
Stream
Audio codec setting...
Manual - Page 45
...select this button to 40. Snapshot and time display setting
Adjust the photo size specifications and choose whether to mark time on requirement or application (3) "Video size" Click the down.../62 Network Camera User's Manual
(2) "Video codec" The Network Camera supports three kind of higher network bandwidth consumption. (7) "Video Quality type" Setting optimizes bandwidth utilization and video...
Manual - Page 52
... the storage device is Kiwi Syslog Daemon. Syslog
The Network camera supports log the system messages on the facility for receiving log from remote machine. An example is not writeprotected. If the SD card can choose upload or delete files. Check "Setup‖ and ―Enable‖ then input the "IP address‖...
Manual - Page 54
... ―Root Password‖. to restore the factory default settings. Upload setting backup file: Click Browse... Please be aware that the model and firmware version of the device should not turn off the power during updating the firmware and wait for the device and user-defined scripts. -- "Reboot system" The "Reboot" button will restart and require the installer program to...
Manual - Page 55
... broken during the procedure, it might possibly cause serious damage to set up the network again.
55/62 The system will restart and require the installer program to the Network Camera. Network Camera User's Manual
Warning: The upgrade firmware procedure cannot be interrupted. Note: When upgrade firmware please wait for 120~210 seconds, and then you can connect...
Manual - Page 56
...If the problem is ...set up . It must support UPnP port forwarding and enable this function
first!!
2. Plug power cord to camera Network page. Go to camera. 4. Q3: The Network Camera will be installed and work if a firewall exists on the network? Connect camera RJ45 cable to Internet. 3. Troubleshooting...Camera User's Manual
Appendix
A. If it is, check the item, and the led should light up ;...
Manual - Page 60
...Install the audio codec in ―Maintenance‖ page to play the recorded video file. Is it is different form the environment. The internal material has the operational temperature, and it normal? And then adjust the camera focus manually. (2) The image may be out of upgrade firmware... The process of focus. Network Camera User's Manual
of the flashing, the network camera begins to...
Manual - Page 62
.../Zoom Range Support auto tracking function Support multi - direction movement Pan : 355°, Tilt : 135° 10X optical zoom , 4X digital zoom
- Power Input: 100-240VAC, 50/60Hz, 0.7A Output: 12VDC, 1.5A Consumption: Max 8 W 802.3af compliant Power over Ethernet(wired model)
- Weight NET.425g (Wired Model) NET. 455g (Wireless Model)
62/62 Technical specifications
- Protocol...
EU Declaration of Conformity - Page 2
... named standards and regulations.
2014/12/5
The symbol confirms that the following apparatus
Type
Network Camera
Brandname LevelOne
Product FCS-1041
Conforms with the essential requirements of the EMC Directive 2004/108/EC, based on the following specifications applied:
EU harmonised standards EN55022:2010+AC:2011Class B EN55024:2010 EN61000-3-2:2006+A1:2009...
LevelOne FCS-1041 Reviews
We have not received any reviews for LevelOne yet.