K200 Hardware Maintenance Manual
Page 2
... Replacing the mouse 42 Replacing the External speaker 43 Completing the installation 43 Chapter 8. Statement 46 ii Symptom-to-FRU Index 22 Hard disk drive boot error 22 Power Supply Problems 23 Beep symptoms 24 POST error codes 25 Undetermined problems 27 Chapter 7. Additional Service Information 45 Power management 45 Automatic...
... Replacing the mouse 42 Replacing the External speaker 43 Completing the installation 43 Chapter 8. Statement 46 ii Symptom-to-FRU Index 22 Hard disk drive boot error 22 Power Supply Problems 23 Beep symptoms 24 POST error codes 25 Undetermined problems 27 Chapter 7. Additional Service Information 45 Power management 45 Automatic...
K200 Hardware Maintenance Manual
Page 15
... the Setup Utility program. For an explanation of these messages, refer to help determine the cause of BIOS is installed on all display controls to boot up in the computer you select an incorrect drive.
... the Setup Utility program. For an explanation of these messages, refer to help determine the cause of BIOS is installed on all display controls to boot up in the computer you select an incorrect drive.
K200 Hardware Maintenance Manual
Page 22
.... Select Disable or Enable and press Enter. 6. See the information displayed on page 16). 2. Turn off your computer does not start up (boot) from a device such as the CD-ROM, diskette, or hard disk as OnBoard SiS USB2.0 Controller, USB Keyboard Legacy Support, USB Mouse Legacy... Support, Onboard Audio DEVICE, Onboard LAN Control, Boot from any boot device. Note: If you do the following procedures to startup from Onboard LAN and so on the computer. Select OnBoard SiS USB1.1 Controller....
.... Select Disable or Enable and press Enter. 6. See the information displayed on page 16). 2. Turn off your computer does not start up (boot) from a device such as the CD-ROM, diskette, or hard disk as OnBoard SiS USB2.0 Controller, USB Keyboard Legacy Support, USB Mouse Legacy... Support, Onboard Audio DEVICE, Onboard LAN Control, Boot from any boot device. Note: If you do the following procedures to startup from Onboard LAN and so on the computer. Select OnBoard SiS USB1.1 Controller....
K200 Hardware Maintenance Manual
Page 23
... permanently change the configured startup device sequence, do the following: 1. Select Advanced BIOS Features. 3. Select the devices for the 1st Boot Device, the 2nd Boot Device, the 3rd Boot Deviece and the 4th Boot Device. 4. Using the Setup Utility the F12 key rather than leaving it pressed when turning on page 16). 2. Select the...
... permanently change the configured startup device sequence, do the following: 1. Select Advanced BIOS Features. 3. Select the devices for the 1st Boot Device, the 2nd Boot Device, the 3rd Boot Deviece and the 4th Boot Device. 4. Using the Setup Utility the F12 key rather than leaving it pressed when turning on page 16). 2. Select the...
K200 Hardware Maintenance Manual
Page 24
No operating system installed on Install an operating system on page 13. The most likely cause is not in the boot Check the configuration and ensure sequence in the boot sequence. Notes • If you have both an error message and an incorrect audio response diagnose the error message first....error symptoms in the first part of this index, go to -FRU index lists error symptoms and possible causes. Hard disk drive boot error A hard disk drive boot error (error codes 1962 and I999030X) can also be used to have the following causes. This index can have available when ...
No operating system installed on Install an operating system on page 13. The most likely cause is not in the boot Check the configuration and ensure sequence in the boot sequence. Notes • If you have both an error message and an incorrect audio response diagnose the error message first....error symptoms in the first part of this index, go to -FRU index lists error symptoms and possible causes. Hard disk drive boot error A hard disk drive boot error (error codes 1962 and I999030X) can also be used to have the following causes. This index can have available when ...
K200 Hardware Maintenance Manual
Page 25
... operating systems programs format the hard disk drive. Power Supply Problems If you suspect a power problem, use the following : 1. Attempt to -FRU Index Error The boot sector on Switch continuity. 23 Chapter 6. Symptom-to back-up drive is defective.
... operating systems programs format the hard disk drive. Power Supply Problems If you suspect a power problem, use the following : 1. Attempt to -FRU Index Error The boot sector on Switch continuity. 23 Chapter 6. Symptom-to back-up drive is defective.
K200 Hardware Maintenance Manual
Page 27
.... This series of the system and some basic system-board operations • Checks the memory operation • Starts the video operation • Verifies that the boot drive is working If the POST detects a problem, an error message appears on the system, it performs a series of tests that check the operation of...
.... This series of the system and some basic system-board operations • Checks the memory operation • Starts the video operation • Verifies that the boot drive is working If the POST detects a problem, an error message appears on the system, it performs a series of tests that check the operation of...
K200 Hardware Maintenance Manual
Page 29
...hard disk drive is jumpered as a slave. 1. Power-on the computer to find the failing device or adapter. Make sure you find a suitable boot device. a. Diskette drive 3. Any adapters c. If all devices and adapters have bootable media. External devices (modem, printer, or mouse) b. ...memory e. Memory modules d. Hard disk drive h. External Cache f. Symptom-to-FRU Index POST Error Message Reboot and Select proper Boot device or Insert Boot Media in selected Boot device Description/Action The BIOS was unable to re-test the system. 4. Power-off the computer. 2.
...hard disk drive is jumpered as a slave. 1. Power-on the computer to find the failing device or adapter. Make sure you find a suitable boot device. a. Diskette drive 3. Any adapters c. If all devices and adapters have bootable media. External devices (modem, printer, or mouse) b. ...memory e. Memory modules d. Hard disk drive h. External Cache f. Symptom-to-FRU Index POST Error Message Reboot and Select proper Boot device or Insert Boot Media in selected Boot device Description/Action The BIOS was unable to re-test the system. 4. Power-off the computer. 2.
K210 User's Guide
Page 13
• Connect the monitor signal cable to the on-board graphics card connector if the model you purchased is not equipped with an external graphics card. 1.5 Keyboard [B-1] [B-2] (This picture is only a sketch map for models with the "Rescue System" feature. LVT key, available for the keyboard, it does not show the detail of the key) [B-1] - Press this key under Windows system to launch "Rescue System" when the "Lenovo" screen appears during booting. 8 User Guide 31033098_IdeaCentre K UG_EN.indd 8 2008.2.20 6:40:11 PM Press this key to launch the IE. [B-2] -
• Connect the monitor signal cable to the on-board graphics card connector if the model you purchased is not equipped with an external graphics card. 1.5 Keyboard [B-1] [B-2] (This picture is only a sketch map for models with the "Rescue System" feature. LVT key, available for the keyboard, it does not show the detail of the key) [B-1] - Press this key under Windows system to launch "Rescue System" when the "Lenovo" screen appears during booting. 8 User Guide 31033098_IdeaCentre K UG_EN.indd 8 2008.2.20 6:40:11 PM Press this key to launch the IE. [B-2] -