Owners Manual
Page 6
...installation. If your floor is wo(_l aml!or frame conslrnclion, y_m may need to reinforce iL Front-loaders use substantially fas|er spin speeds than top-loaders, causing greater vibration, If the floor is md solid, your washer will hear and feel the vibration lhroaghoul your... • Time-delay fuseor circuit breaker is recommended NOTE: It is the personal responsibility and obligation of the washer is recommended to reduce noise transfer. Carpeting and soft tile surfaces are for the minimum spacing allowed Additional spacing should also be Installed on a solidly constructed floor. ....
...installation. If your floor is wo(_l aml!or frame conslrnclion, y_m may need to reinforce iL Front-loaders use substantially fas|er spin speeds than top-loaders, causing greater vibration, If the floor is md solid, your washer will hear and feel the vibration lhroaghoul your... • Time-delay fuseor circuit breaker is recommended NOTE: It is the personal responsibility and obligation of the washer is recommended to reduce noise transfer. Carpeting and soft tile surfaces are for the minimum spacing allowed Additional spacing should also be Installed on a solidly constructed floor. ....
Owners Manual
Page 9
... lhe washing machine top plate diagonally, the machine should nol move up against of the base of the washer Al! When Ihe machine spins al high speed, verify that it is properly leveled,, Put approximately 6 poamts of tanmlrLy in the machine. order. The more the ...agaia, hi" INSTALLATION INSTRUCTIONS = Level adjustment ii _i_iiii_i i? _ /_igher Adjustable feet Adjustable feet • Leveling the washing machine properly prevents excessive noise and vibration, Install the appliance on the floor and then check that the appliance is perfectly levet (Use a level) • After the washer ...
... lhe washing machine top plate diagonally, the machine should nol move up against of the base of the washer Al! When Ihe machine spins al high speed, verify that it is properly leveled,, Put approximately 6 poamts of tanmlrLy in the machine. order. The more the ...agaia, hi" INSTALLATION INSTRUCTIONS = Level adjustment ii _i_iiii_i i? _ /_igher Adjustable feet Adjustable feet • Leveling the washing machine properly prevents excessive noise and vibration, Install the appliance on the floor and then check that the appliance is perfectly levet (Use a level) • After the washer ...
Owners Manual
Page 20
...tighten hose connections tap or washer, • House drain pipes are in firm contact with the floor, whi_e the washer is in the spin cycle with automatic safety [unctions which detect and diagnnse problems at an early stage and react appropriately° When the machine dees not ... unevenly distributed in the house Fully open , Water inlet hose [s bent. • The filter of balance Stop and redistribute wash toad, Vibrating noise * Have all the feet resting firmly on the ground? Excessive suds • Too much detergent or unsuitable detergent Reduce detergent amount or use low...
...tighten hose connections tap or washer, • House drain pipes are in firm contact with the floor, whi_e the washer is in the spin cycle with automatic safety [unctions which detect and diagnnse problems at an early stage and react appropriately° When the machine dees not ... unevenly distributed in the house Fully open , Water inlet hose [s bent. • The filter of balance Stop and redistribute wash toad, Vibrating noise * Have all the feet resting firmly on the ground? Excessive suds • Too much detergent or unsuitable detergent Reduce detergent amount or use low...
Service Manual
Page 25
...is perfectly level as follows: Check the leveling of clothing. YES Remove the transit bolts NO and Base packing. When the machine is spinning in high spin (Refer to 3 kg) of the washer with a Level and check that the washer is stable. After the washer is stable. NO... washer installed on a solidly constructed floor? If you do not have the unbalance part, put 4.5 to 6.5 lbs (2 to section 7-2). VIBRATION & NOISE IN SPIN Base Packing Level Unbalance Part Higher LNouctk Adjustable feet Lower Adjustable feet Have all the transit bolts and base packing been removed? YES If it...
...is perfectly level as follows: Check the leveling of clothing. YES Remove the transit bolts NO and Base packing. When the machine is spinning in high spin (Refer to 3 kg) of the washer with a Level and check that the washer is stable. After the washer is stable. NO... washer installed on a solidly constructed floor? If you do not have the unbalance part, put 4.5 to 6.5 lbs (2 to section 7-2). VIBRATION & NOISE IN SPIN Base Packing Level Unbalance Part Higher LNouctk Adjustable feet Lower Adjustable feet Have all the transit bolts and base packing been removed? YES If it...
Service Manual
Page 26
... Press the Quick Cycle button, the spin speed is displayed. 6) Press the Start/Pause button. 7) Press the Beeper button repeatedly to set spin speed (600, 900, 1020, 1120 rpm) and check if there is vibration and noise. 8) If there is no vibration and noise, increase the spin speed by 50 and 100 rpm). If... it can not reduce the spin speed. 10) If vibration and noise are reduced, press the Quick Cycle button to store (2 beep sounds). * ...
... Press the Quick Cycle button, the spin speed is displayed. 6) Press the Start/Pause button. 7) Press the Beeper button repeatedly to set spin speed (600, 900, 1020, 1120 rpm) and check if there is vibration and noise. 8) If there is no vibration and noise, increase the spin speed by 50 and 100 rpm). If... it can not reduce the spin speed. 10) If vibration and noise are reduced, press the Quick Cycle button to store (2 beep sounds). * ...